Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 195 (AUTOMATIC TRANSMISSION - VT25-E - INTRODUCTION & REPAIR INSTRUCTIONS)COMPONENT LOCATORDISASSEMBLED VIEWS
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Disassembled Views
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Disassembled Views
WARNING: This page is about a different car, the 2005 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
| Callout | Component Name |
|---|---|
| 1 | Torque Converter Assembly |
| 2 | Torque Converter and Differential Housing Seal Assembly |
| 3 | Front Wheel Drive Shaft Oil Seal Assembly - 2WD |
| 3a | Front Wheel Drive Shaft Oil O-Ring Seal - F4WD |
| 4 | Torque Converter and Differential Housing Assembly - Model Specific |
| 5 | Torque Converter and Differential Housing Bolt/Screw - M8 x 1.25 x 35 |
| 6 | Variable Driven Pulley Bearing Assembly |
| 7 | Front Differential Drive Pinion Gear Shim |
| 8 | Front Differential Drive Pinion Gear Bearing Cup |
| 9 | Front Differential Drive Pinion Gear Assembly |
| 10 | Automatic Transmission Case Plug |
| 11 | Transmission Fluid Baffle |
| 12 | Transmission Fluid Baffle Bolt/Screw - M6 x 1.0 x 17 |
| 13 | Front Differential Bearing Shim |
| 14 | Front Differential Carrier Bearing Cup |
| 15 | Drive Link Assembly |
| 16 | Driven Sprocket Retaining Ring |
| 17 | Driven Sprocket |
| 18 | Automatic Transmission Fluid Pump O-Ring Seal |
| 19 | Automatic Transmission Fluid Pump Bolt/Screw - M6 x 1.0 x 55 |
| 20 | Bolt/Screw - M6 x 1.0 x 70 |
| 21 | Automatic Transmission Fluid Filter Retainer |
| 23 | Automatic Transmission Fluid Pump Assembly |
| 25 | Automatic Transmission Fluid Pump Seal |
| 26 | Automatic Transmission Fluid Filter Assembly |
| 27 | Automatic Transmission Fluid Filter O-Ring Seal |
| 28 | Automatic Transmission Fluid Filter O-Ring Seal |
| 29 | Drive Sprocket Thrust Washer |
| 29 | Drive Sprocket Thrust Washer |
| 30 | Drive Sprocket |
| 32 | Front Differential Carrier Assembly |
| 33 | Park Pawl Shaft Hole Plug |
| 34 | Park Pawl Actuator Guide Pin |
| 35 | Park Pawl Reaction Pin |
| 36 | Park Pawl |
| 37 | Park Pawl Spring |
| 38 | Park/Neutral Position Switch Assembly Bolt/Screw - M6 x 1.0 x 18.4 |
| 39 | Park/Neutral Position Switch Assembly |
| 40 | Manual Shift Shaft |
| 41 | Manual Shift Shaft Seal Assembly |
| 42 | Park Pawl Actuator Guide |
| 43 | Park Pawl Actuator Assembly |
| 44 | Manual Shift Shaft Retainer |
| 45 | Manual Shaft Detent Lever |
| 46 | Manual Shift Shaft Nut |
| 47 | Manual Valve Link |
| 48 | Manual Valve Link Spring |
| 49 | Transmission Case Locator Pin |
| 50 | Automatic Transmission Case Assembly |
| 51 | Transmission Fluid Fill Lower Tube Seal |
| 52 | Transmission Fluid Fill Lower Tube |
| 53 | Transmission Fluid Fill Lower Tube Plug |
| 54 | Transmission Fluid Cooler Pipe Fitting Seal |
| 55 | Automatic Transmission Fluid Pressure Test Hole Plug |
| 56 | Transmission Fluid Baffle - Top |
| 57 | Transmission Fluid Baffle - Bottom |
| 58 | Transmission Fluid Baffle Bolt/Screw - M5 x 0.8 x 13 |
| Callout | Component Name |
|---|---|
| 49 | Transmission Case Locator Pin |
| 50 | Automatic Transmission Case Assembly |
| 60 | Control Valve Body Cover Bolt/Screw - M6 x 1.0 x 25 |
| 61 | Automatic Transmission Vent Cap |
| 62 | Automatic Transmission Vent Cap O-Ring |
| 63 | Automatic Transmission Vent Cap Insert |
| 64 | Automatic Transmission Vent Cap Insert O-Ring |
| 67 | Control Valve Body Cover |
| 68 | Control Valve Body Cover Gasket |
| 69 | Manual Shaft Detent Assembly Bolt/Screw - M6 x 1.0 x 30 |
| 70 | Manual Shaft Detent Assembly |
| 71 | Control Valve Body Bolt/Screw - M6 x 1.0 x 80 |
| 72 | Control Valve Body Assembly |
| 73 | Control Valve Body Spacer - with Gasket - Plate |
| 74 | Automatic Transmission Input and Output Speed Sensor Assembly |
| 75 | Bolt/Screw - M6 x 1.0 x 17 |
| 76 | Control Valve Body Locator Pin |
| 77 | Automatic Transmission Case Cover - O-Ring - Seal |
| 78 | Lube Oil Pipe |
| 79 | Control Valve Body Bolt/Screw - M5 x 0.8 x 78 |
| 80 | Stator Shaft Seal |
| 81 | Stator Shaft Assembly |
| 82 | Reverse Clutch Piston Assembly |
| 83 | Reverse Clutch Spring Assembly |
| 84 | Reverse Clutch Spring Retaining Ring |
| 85 | Reverse Clutch Hub Thrust Washer |
| 86 | Reverse Clutch - with Input Internal Gear - Hub Assembly |
| 87 | Reverse Clutch - Waved - Plate |
| 88 | Reverse Clutch Plate Assembly - Spline OD |
| 89 | Reverse Clutch Plate Assembly - Spline ID |
| 90 | Reverse Clutch Plate Set |
| 91 | Reverse Clutch Backing Plate |
| 92 | Reverse Clutch Backing Plate Retaining Ring |
| 93 | Variable Drive Pulley Assembly |
| 94 | Variable Drive Pulley Follower Pin |
| 95 | Variable Drive Pulley Follower |
| 96 | Variable Drive Pulley Follower Spring |
| 97 | Automatic Transmission Case Cover Assembly |
| 98 | Variable Drive Pulley Opening Cover Seal |
| 99 | Variable Drive Pulley Bearing Retaining Ring |
| 100 | Variable Drive Pulley Bearing Retainer |
| 101 | Variable Drive Pulley Bearing Retainer Nut - M6 x 1.0 |
| 102 | Variable Drive Pulley Opening Cover Seal |
| 103 | Automatic Transmission Case Cover Seal |
| 104 | Variable Drive Pulley Opening Cover |
| 105 | Variable Pulley Opening Cover Bolt/Screw - M6 x 1.0 x 25 |
| 106 | Variable Driven Pulley Assembly |
| 107 | Variable Drive Belt Assembly |
| 108 | Automatic Transmission Case Cover Bolt/Screw - M8 x 1.25 x 40 |
| 109 | Variable Driven Pulley Opening Cover Seal |
| 110 | Automatic Transmission Case Cover - O-Ring - Seal |
| 111 | Variable Driven Pulley Bearing Retainer - Selective |
| 112 | Variable Driven Pulley Bearing Retainer Bolt/Screw - M6 x 1.0 x 25 |
| 113 | Variable Driven Pulley Opening Cover Seal |
| 114 | Variable Driven Pulley Opening Cover |
| 115 | Variable Driven Pulley Opening Cover Bolt/Screw - M8 x 1.25 x 50 |
| Callout | Component Name |
|---|---|
| 200 | Control Valve Body Cover Wiring Connector Hole Seal |
| 201 | Control Solenoid Valve Assembly |
| 202 | Manual Valve |
| 203 | Automatic Transmission Fluid Pump Pressure Screen Assembly |
| 204 | Control Valve Body Spacer - with Gasket - Plate Assembly |
| 205 | Control Valve Body Ball Check Valve |
| 206 | Control Solenoid Valve Locator Pin |
| 207 | Control Valve Body Assembly |
| 208 | Bore Plug Retainer |
| 209 | Bore Plug |
| 210 | Bore Plug Seal |
| 211 | Line 2 Pressure Regulator Valve Spring |
| 212 | Line 2 Pressure Regulator Valve |
| Callout | Component Name |
|---|---|
| 300 | Bore Plug Retainer |
| 301 | Bore Plug |
| 302 | Bore Plug Seal |
| 303 | Forward and Reverse Clutch Valve Spring |
| 304 | Forward and Reverse Clutch Valve |
| 305 | Control Valve Body |
| 306 | Valve Spring Seat |
| 307 | TCC Control Valve Spring |
| 308 | TCC Control Valve |
| 309 | Line Limit Valve Spring |
| 310 | Line Limit Valve |
| 311 | Actuator Feed Limit Valve Spring |
| 312 | Actuator Feed Limit Valve |
| 313 | Primary Limit Valve Spring |
| 314 | Primary Limit Valve |
| Callout | Component Name |
|---|---|
| 206 | Control Solenoid Valve Locator Pin |
| 300 | Bore Plug Retainer |
| 301 | Bore Plug |
| 302 | Bore Plug Seal |
| 305 | Control Valve Body |
| 315 | Line 1 Pressure Regulator Valve Spring |
| 316 | Line 1 Pressure Regulator Valve |
| 317 | Variable Ratio Control Valve Lever Assembly |
| 318 | Variable Ratio Control Valve Spring |
| 319 | TCC Regulator Valve |
| 320 | TCC Regulator Apply Valve Spring |
| 321 | Clutch Boost Valve Spring |
| 322 | Clutch Boost Valve |
| Callout | Component Name |
|---|---|
| 400 | End Cover Retaining Ring |
| 401 | Pump End Cover |
| 402 | Pump End Cover O-Ring Seal |
| 403 | Pressure Plate Spring |
| 404 | Pressure Plate |
| 405 | Cam Ring |
| 406 | Pump Drive Shaft Retaining Ring |
| 407 | Pump Rotor Vane |
| 408 | Pump Rotor |
| 409 | Pump Thrust Plate |
| 410 | Cam Ring Dowel Pin |
| 411 | Pump O-Ring Seal - Inner |
| 412 | Pump Housing |
| 414 | Pump Drive Shaft |
| 415 | Pump Drive Shaft Seal |
| Callout | Component Name |
|---|---|
| 500 | Variable Drive Pulley Assembly |
| 501 | Forward Clutch Piston Assembly |
| 502 | Forward Clutch Piston - Belleville - Spring |
| 503 | Forward Clutch Spring Washer - Some Models |
| 503 | Forward Clutch Spring Washer - Some Models |
| 504 | Forward Clutch Piston Spring Retaining Ring |
| 505 | Sun Gear |
| 506 | Sun Gear Thrust Washer |
| 507 | Input Shaft Bearing Assembly - Inner |
| 508 | Input Shaft Fluid Passage Sleeve |
| 509 | Input Shaft Assembly |
| 510 | Input Shaft Bearing Assembly - Outer |
| 511 | Input Shaft Fluid Seal Ring |
| 512 | Input Shaft - O-Ring - Seal |
| 513 | Input Shaft - Split Spiral - Fluid Seal Ring |
| 514 | Forward Clutch - Waved - Plate |
| 515 | Forward Clutch Plate Assembly - Spline OD |
| 515 | Forward Clutch Plate Assembly - Spline OD |
| 516 | Forward Clutch Plate Assembly - Spline ID |
| 516 | Forward Clutch Plate Assembly - Spline ID |
| 517 | Forward Clutch Backing Plate |
| 518 | Forward Clutch Plate Set |
| 519 | Forward Clutch Backing Plate Retaining Ring |
| 520 | Input Internal Gear Thrust Washer |
| 521 | Automatic Transmission Input Shaft Speed Sensor Reluctor Ring Assembly |
| 522 | Automatic Transmission Input Shaft Speed Sensor Reluctor Ring Retaining Ring |
| Callout | Component Name |
|---|---|
| 600 | Front Differential Carrier Bearing Assembly |
| 600 | Front Differential Carrier Bearing Assembly |
| 601 | Front Differential Carrier Assembly - 2WD |
| 601a | Front Differential Carrier Assembly - F4WD |
| 602 | Front Differential Pinion Gear Shaft Pin |
| 603 | Front Differential Pinion Shaft |
| 604 | Front Differential Carrier Thrust Washer - Some Models |
| 605 | Front Differential Side Gear |
| 605 | Front Differential Side Gear |
| 606 | Front Differential Pinion Gear |
| 606 | Front Differential Pinion Gear |
| 607 | Front Differential Pinion Gear Thrust Washer - Some Models |
| 607 | Front Differential Pinion Gear Thrust Washer - Some Models |
| 608 | Front Differential Side Gear Thrust Washer - Some Models |
| 608 | Front Differential Side Gear Thrust Washer - Some Models |
| Callout | Component Name |
|---|---|
| 700 | Front Differential Drive Pinion Gear Bearing Assembly |
| 701 | Front Differential Drive Pinion Gear and Transfer Gear Assembly |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.