Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2001 Chevrolet Cutaway 6.5 FFACTORY OEM SERVICE PROCEDURE
Engine Controls Self-Diagnostics - 6.5L
- Model Identification
- Introduction
- Self-Diagnostic System
- Programming
- Inspection/Maintenance Procedures
- Summary
- Diagnostic Trouble Code Definitions
- System Tests
- Diagnostic Tests
- Notes
- DTC P0112: Intake Air Temperature Sensor Circuit Low Voltage
- DTC P0113: Intake Air Temperature Sensor Circuit High Voltage
- DTC P0117: Engine Coolant Temperature Sensor Circuit Low Voltage
- DTC P0118: Engine Coolant Temperature Sensor Circuit High Voltage
- DTC P0121: Accelerator Pedal Position Sensor 1 Circuit Performance
- DTC P0122: Accelerator Pedal Position Sensor 1 Circuit Low Voltage
- DTC P0123: Accelerator Pedal Position Sensor 1 Circuit High Voltage
- DTC P0126: Insufficient ECT For Stable Operation
- DTC P0182: Fuel Temperature Sensor Circuit Low Voltage
- DTC P0183: Fuel Temperature Sensor Circuit High Voltage
- DTC P0215: Engine Shutoff Solenoid Control Circuit
- DTC P0216: Injection Timing Control System
- DTC P0219: Engine OVERSPEED Condition
- DTC P0220: Accelerator Pedal Position Sensor 2 Circuit
- DTC P0221: Accelerator Pedal Position Sensor 2 Circuit Performance
- DTC P0222: Accelerator Pedal Position Sensor 2 Circuit Low Voltage
- DTC P0223: Accelerator Pedal Position Sensor 2 Circuit High Voltage
- DTC P0225: Accelerator Pedal Position Sensor 3 Circuit
- DTC P0226: Accelerator Pedal Position Sensor 3 Circuit Performance
- DTC P0227: Accelerator Pedal Position Sensor 3 Circuit Low Voltage
- DTC P0228: Accelerator Pedal Position Sensor 3 Circuit High Voltage
- DTC P0231: Fuel/Lift Pump Feedback Circuit Low Voltage
- DTC P0236: Turbocharger Boost System
- DTC P0237: Turbocharger Boost Pressure Sensor Circuit Low Voltage
- DTC P0238: Turbocharger Boost Pressure Sensor Circuit High Voltage
- DTC P0251: Injection Pump Cam System
- DTC P0263: Cylinder No. 1 Balance System
- DTC P0266: Cylinder No. 2 Balance System
- DTC P0269: Cylinder No. 3 Balance System
- DTC P0272: Cylinder No. 4 Balance System
- DTC P0275: Cylinder No. 5 Balance System
- DTC P0278: Cylinder No. 6 Balance System
- DTC P0281: Cylinder No. 7 Balance System
- DTC P0284: Cylinder No. 8 Balance System
- DTC P0300: Engine Misfire Detected
- DTC P0301: Cylinder No. 1 Misfire Detected
- DTC P0302: Cylinder No. 2 Misfire Detected
- DTC P0303: Cylinder No. 3 Misfire Detected
- DTC P0304: Cylinder No. 4 Misfire Detected
- DTC P0305: Cylinder No. 5 Misfire Detected
- DTC P0306: Cylinder No. 6 Misfire Detected
- DTC P0307: Cylinder No. 7 Misfire Detected
- DTC P0308: Cylinder No. 8 Misfire Detected
- DTC P0335: Crankshaft Position Sensor Circuit Performance
- DTC P0370: Timing Reference High Resolution
- DTC P0380: Glow Plug Circuit Performance
- DTC P0601: Control Module Read Only Memory (ROM)
- DTC P0602: Control Module Not Programmed
- DTC P0603: Control Module Long Term Memory Reset
- DTC P0604: Control Module Random Access Memory (Ram)
- DTC P0605: Control Module Programming Read Only Memory (ROM)
- DTC P0606: Control Module Internal Performance
- DTC P0607: Control Module Performance
- DTC P0719: TCC/Stoplight Switch Open Or Stuck In Off Position During Deceleration
- DTC P0724: TCC/Stoplight Switch Closed Or Stuck In On Position During Acceleration
- DTC P1125: Accelerator Pedal Position System
- DTC P1214: Injection Pump Timing Offset Error
- DTC P1216: Fuel Solenoid Response Time Too Short
- DTC P1217: Fuel Solenoid Response Time Too Long
- DTC P1218: Injection Pump Calibration Circuit
- DTC P1627: Analog-To-Digital Converter Circuit
- DTC P1635: Pcm 5-Volt Reference Low
- DTC P1641: Malfunction Indicator Light Control Circuit
- DTC P1643: Wait To Start Light Control Circuit
- DTC P1654: Service Throttle Soon Light Control Circuit
- DTC P1656: WASTEGATE Solenoid Control Circuit
- DTC P1683: Control Module Ignition Off Timer Performance
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
