Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001CAVALIER LS, 2.4 TREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 13 (MEMORY SYSTEMS)DIAGNOSTIC TESTSDTC B2606: SEAT REAR VERTICAL POSITION SENSOR FAILURE (SCM)TESTING
2001 Chevrolet Cavalier LS, 2.4 T
DTC B2606: Seat Rear Vertical Position Sensor Failure (SCM): Testing
2001 Chevrolet Cavalier LS, 2.4 TSECTION Testing
WARNING: This page is about a different car, the 2000 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
- If diagnostic system check was performed, go to next step. If diagnostic system check has not been performed, go to DIAGNOSTIC SYSTEM CHECK under SELF-DIAGNOSTIC SYSTEM.
- Using scan tool, display SCM DTCs. If DTC B2606 is set as history, go to next step. If DTC B2606 is not set as history, go to step 6 .
- Using scan tool, monitor SCM data display for left seat front vertical position sensor. Attempt to operate rear of left seat using power seat switch. If scan tool does not display 0.10-4.78 volts, go to next step. If scan tool displays 0.10-4.78 volts, go to step 12 .
- Turn ignition off. Disconnect left seat lower motor connector C4. Turn ignition on. Using DVOM, measure voltage between left seat lower motor connector C4 terminal "C" (Purple wire) and ground. See Figure . If voltage is 4.0-5.5 volts, go to next step. If voltage is not 4.5-5.5 volts, go to step 7 .
- Measure voltage between left seat lower motor connector C4 terminals "A" (Black wire) and "C" (Purple wire). If voltage is not 4.0-5.5 volts, go to step 8 . If voltage is 4.0-5.5 volts, go to step 10 .
- Turn ignition off. Disconnect left seat lower motor connector C4. Turn ignition on. Using DVOM, measure voltage between left seat motor connector C4 terminal "B" (Tan wire) and ground while operating rear of left seat using power seat switch. If voltage is not 3.5-5.5 volts, go to step 9 . If voltage is 3.5-5.5 volts, go to step 10 .
- Check for open, short to ground or short to voltage in Purple wire between left seat lower motor connector C4 and SCM connector C1. If circuit is okay, go to step 11 . If faulty circuit is found and repaired, go to step 14 .
- Check for open or short to voltage in Black wire between left seat lower motor connector C4 and SCM connector C1. If circuit is okay, go to step 11 . If faulty circuit s found and repaired, go to step 14 .
- Check for open, short to ground or short to voltage in Tan wire between left seat lower motor connector C4 and SCM connector C1. If circuit is okay, go to step 11 . If faulty circuit s found and repaired, go to step 14 .
- Replace left seat adjuster motor assembly. See POWER SEATS - CORVETTE article. After repairs, go to step 14 .
- Replace SCM. See SEAT CONTROL MODULE under REMOVAL & INSTALLATION. After repairs, go to step 14 .
- Check left seat rear vertical position sensor wiring and connectors for intermittent malfunctions. See WIRING DIAGRAMS . If problem is not found, go to next step. If problem circuit or connector is repaired, go to step 14 .
- Turn ignition off. Reconnect all disconnected components and connectors. Turn ignition on and clear any DTCs. Wait 2 seconds. If DTC B2606 sets as history, go to step 11 . If DTC B2606 does not set as history, system is okay at this time.
- Turn ignition off. Reconnect all disconnected components and connectors. Turn ignition on and clear any DTCs. If DTC resets, go to DIAGNOSTIC SYSTEM CHECK under SELF-DIAGNOSTIC SYSTEM.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.