Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2013128I 2D CONVERTIBLE, ENG CD N52, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1838 (FRONT AXLE - REPAIR)
2013 BMW 128i 2D Convertible, Eng CD N52, Standard Trans
Section 1838 (Front Axle - Repair)
2013 BMW 128i 2D Convertible, Eng CD N52, Standard TransSECTION Section 1838 (Front Axle - Repair)
WARNING: This page does not describe the selected car, but rather 18 other vehicles, including the 2015 BMW Alpina B7L xDrive, 2015 BMW Alpina B7 xDrive, 2015 BMW 750i xDrive, 2015 BMW 750Li xDrive, and 2015 BMW 740Li xDrive. However, it is still accessible from the selected car via links, so may be relevant.
- General And Safety Information
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- 00 Safety instructions for handling oil
- 00..... Lifting the vehicle using a vehicle hoist
- 00..... Raising vehicle with trolley jack
- 31 00 Mobile table lift
- 31..... Front axle overview
- 31..... Overview of front axle differential/output shafts
- 31 00... Front axle + steering: wheel/chassis alignment check must be carried out after the following work
- 31 00... Information on replacing shock absorbers
- 31 00... Instructions (chassis components made of aluminium)
- 31 00... Notes regarding bent control arm or tie rod
- 31 00... Notes on repairing threads
- Front Axle Suspension
- Front Sub-Frame
- Struts With Rubber Mounts
- 31 12 075 Checking both tension struts
- 31 12 003 Removing and installing / replacing top right control arm
- 31 12 004 Removing and installing/replacing bottom left or right control arm
- 31 12 050 Removing and installing/replacing left or right trailing link
- 31 12 002 Removing and installing/replacing top left control arm
- 31 12 134 Replacing rubber mount in left or right trailing link
- Wheel Bearings And Stub Axle
- Spring Strut
- Spring With Suspension
- Stabilizer Bar
- Front Axle Gearbox
- 31 50... Check/change front axle differential oil
- 31 50 001 Removing and installing/replacing front axle differential
- 31 51 060 Replacing O-ring for front axle differential on right
- 31 51 010 Replacing radial seal for drive flange of front axle differential
- 31 51 020 Replacing shaft seal for right output shaft
- 31 51 015 Replacing shaft seal for left output shaft
- 31 51 065 Replacing O-ring for bearing block
- Differential With Bearings
- Output Shaft
- 31 51 020 Replacing shaft seal for right output shaft
- 31 51 015 Replacing shaft seal for left output shaft
- 31 60... Notes on removing and installing Low Profile band clamps
- 31 60 005 Removing and installing/replacing both output shafts
- 31 60 000 Removing and installing/replacing left or right output shaft
- 31 60 530 Replacing an output shaft gaiter (on transmission side) (output shaft removed)
- 31 60 535 Replacing two gaiters on output shaft(s) (output shaft(s) removed)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.