E60, E61, E63, E64 - PDC Control Unit

2006 BMW M6SECTION E60, E61, E63, E64 - PDC Control Unit

Installation location 

On the BMW 5-Series, the PDC control unit is located under the spare wheel in the luggage compartment well. The PDC control unit is fitted in the function carrier (illustration shows E60).

On the BMW 6-Series, the function carrier is in front of the battery in the luggage compartment well.

Fig 1: Locating PDC Control Unit
G00431699Courtesy of BMW OF NORTH AMERICA, INC.

Construction 

The PDC control unit is connected to the rest of the vehicle electrical system by 3 plug connectors.

Pin assignment for X300, 12-pin 

PIN ASSIGNMENT FOR X300, 12-PIN

Pin Type Description
1 V Power supply, terminal 15
For vehicles from 03/2004: terminal 30g (active)
2 E/A CAN high on K-CAN
3 --- ---
4 --- ---
5 --- ---
6 M Earth, terminal 31
7 --- ---
8 E/A CAN low on K-CAN
9 --- ---
10 --- ---
11 --- ---
12 --- ---
  E/A = Input and output
M = Earth
V = Supply
For current specifications regarding pin assignment, please refer to BMW diagnosis system

Pin assignment for X18013, 18-pin 

PIN ASSIGNMENT FOR X18013, 18-PIN

Pin Type Description
1 A Earth for ultrasonic sensor, rear right
2 A Earth for ultrasonic sensor, rear left
3 --- ---
4 --- ---
5 A Power supply for ultrasonic sensor, rear middle right
6 A Power supply for ultrasonic sensor, rear middle left
7 A Power supply for ultrasonic sensor, rear right
8 A Power supply for ultrasonic sensor, rear left
9 --- ---
10 A Earth for ultrasonic sensor, rear middle right
11 A Earth for ultrasonic sensor, rear middle left
12 E Signal from ultrasonic sensor, rear middle right
13 E Signal from ultrasonic sensor, rear middle left
14 E Signal from ultrasonic sensor, rear right
15 E Signal from ultrasonic sensor, rear left
16 --- ---
17 --- ---
18 --- ---
  A = Output
E = Input
For current specifications regarding pin assignment, please refer to BMW diagnosis system

Pin assignment for X18362, 18-pin 

PIN ASSIGNMENT FOR X18362, 18-PIN

Pin Type Description
1 A Earth for ultrasonic sensor, front right
2 A Earth for ultrasonic sensor, front left
3 --- ---
4 --- ---
5 A Power supply for ultrasonic sensor, front middle right
6 A Power supply for ultrasonic sensor, front middle left
7 A Power supply for ultrasonic sensor, front right
8 A Power supply for ultrasonic sensor, front left
9 --- ---
10 A Earth for ultrasonic sensor, front middle right
11 A Earth for ultrasonic sensor, front middle left
12 E Signal from ultrasonic sensor, front middle right
13 E Signal from ultrasonic sensor, front middle left
14 E Signal from ultrasonic sensor, front right
15 E Signal from ultrasonic sensor, front left
16 --- ---
17 --- ---
18 --- ---
  A = Output
E = Input
For current specifications regarding pin assignment, please refer to BMW diagnosis system
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.