Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2006760LIREPAIR AND DIAGNOSISQUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
2006 BMW 760Li
Specifications Index
2006 BMW 760LiSECTION Specifications Index
760Li SPECIFICATIONS INDEX
| System | Specification/Procedure | |
|---|---|---|
| Air Conditioning | ||
| Service | TECHNICAL DATA | |
| Torque | TIGHTENING TORQUES | |
| Axle Shaft Nut | ||
| Rear | 310 Ft. Lbs. (420 N.m) | |
| Battery | BATTERY | |
| Brakes | ||
| Bleeding Sequence | BRAKE TESTING AND BLEEDING | |
| Disc Brakes | SPECIFICATIONS | |
| Torque | BRAKES - TIGHTENING TORQUES | |
| Charging | ||
| Generator | NA | |
| Torque | TORQUE SPECIFICATIONS | |
| Drive Belts | ||
| Adjustment | V-RIBBED BELT | |
| Belt Routing | V-RIBBED BELT | |
| Engine Cooling | ||
| General Service Specifications | COOLING SYSTEM | |
| Radiator Cap Pressure | See cap top for specification. | |
| Thermostat R & I | 53 THERMOSTAT AND CONNECTIONS | |
| Water Pump R & I | 51 WATER PUMP WITH DRIVE | |
| Engine Mechanical | ||
| Compression | TECHNICAL DATA | |
| Oil pressure | Oil pressure should be more than 14 psi (96 kPa) at idle and 58-116 psi (400-800 kPa) control pressure. | |
| Overhaul | ENGINE - TECHNICAL DATA | |
| Torque | ENGINE - TIGHTENING TORQUES | |
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or Maint." button. | |
| Flywheel/Flex Plate Torque | FLYWHEEL | |
| Fuel System | ||
| Fuel Filter Location | Under vehicle, forward from fuel tank along fuel feed line behind fuel filter cover. | |
| Fuel Filter R & I | FUEL FILTER | |
| Pressure Release Procedure | NA | |
| Pressure Specification | 87 psi (600 kPa) | |
| Fuel Pressure Test Procedure | CHECKING FUEL FEED PRESSURE (N73) | |
| Ignition | ||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER INDENTIFICATION | |
| Ignition Wires (Routing) | IGNITION WIRES, SPARK PLUGS | |
| Spark Plug | ||
| Type | NGK BKR 6E QUP | |
| Gap | Spark plug gap is not adjustable. | |
| Torque | 23 Ft. Lbs. (31 N.m) | |
| Starting | ||
| Starter | NA | |
| Torque | TORQUE SPECIFICATIONS | |
| Wheel Alignment | ||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS - E65/66 | |
| Torque | TORQUE SPECIFICATIONS | |
| Wheel & Tire | ||
| Wheel Lug Nut Torque | TIGHTENING TORQUES | |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.