Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
2007 Audi S8
Body Exterior
2007 Audi S8SECTION Body Exterior
- 50 - Body - Front
- 55 - Hood, Lids
- Contact corrosion
- Hood
- Trunk lid
- Fuel filler flap
- 57 - Front Doors, Central Locking System, Window Regulators
- Contact corrosion
- Front door
- Window frame and window regulator, removing and installing
- Door window, removing and installing
- Window regulator, removing and installing
- Window regulator motor, removing and installing
- Assembly carrier, removing and installing
- Motor for closing assist, removing and installing
- Motor for window regulator, removing and installing
- Door handle
- Front door handle and lock cylinder, removing and installing
- Removing and installing door lock
- Lock cover, removing and installing
- Mounting bracket, clipping into door lock
- Front door, adjusting
- Door adjustment, checking using adjusting template T40038/2
- Central locking system
- 58 - Rear Doors, Window Regulators
- Contact corrosion!
- Rear doors
- Window frame and window regulator, removing and installing
- Door window, removing and installing
- Window regulator, removing and installing
- Assembly carrier, removing and installing
- Motor for closing assist, removing and installing
- Motor for window regulator, removing and installing
- Rear door handle
- Rear door handle, removing and installing
- Removing and installing door lock
- Mounting bracket, clipping into door lock
- Rear door, adjusting
- Door adjustment, checking using adjusting template T40 038/2
- 60 - Sunroof
- Contact corrosion!
- Sunroof, servicing
- Sunroof, servicing
- Sunroof frame, removing and installing
- Removing and installing wind deflector
- Wind deflector, adjusting
- Wind deflector motor, removing and installing
- Wind deflector motor, performing initialization
- Sunroof motor, removing and installing
- Sunroof panel, removing and installing
- Sunroof panel, removing
- Adjusting panel
- Interior trim, replacing
- Sunroof sliding headliner, removing and installing
- Panel seal, replacing
- Zero position (link guide), adjusting
- "Zero" position of sunroof motor (link guide), checking and adjusting
- Parallel movement, checking and adjusting
- Sunroof, performing initialization and learning phase
- Water drain hoses
- 63 - Bumpers
- Contact corrosion!
- Front bumper
- Front bumper cover, removing and installing
- Assembly overview
- Intake manifold bolting point
- Removing and installing left/right air inlet grille
- Center air inlet grille, removing and installing
- Assembly overview for 12-cylinder vehicles (single frame)
- Air inlet grille for 12-cylinder vehicles (single frame)
- Removing radiator grille
- Remove license plate holder
- ACC cover, removing and installing
- Removing side impact molding
- Bumper cover, removing
- Securing cover to fender
- Wheel spoiler, removing
- Front bumper, removing and installing
- Bracket for bumper, removing and installing
- Front bumper cover, removing and installing
- Rear bumper
- Trailer hitch, removing and installing
- 64 - Glass, Windows
- 66 - Exterior equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.