Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSAUDI2001A6 AVANT QUATTROREPAIR AND DIAGNOSISSUSPENSIONSUSPENSION CONTROL SYSTEMSSELF LEVELING SUSPENSIONLEVEL CONTROL SYSTEM, SERVICINGAPPLICATION OF GROUND CLEARANCES (SETTING DIMENSIONS) FOR SUSPENSIONPROCEDURE

2001 Audi A6 Avant Quattro

Application of ground clearances (setting dimensions) for suspension: Procedure

2001 Audi A6 Avant QuattroSECTION Procedure

Basic setting is carried out via function "11 - Login".
Inserting of special tool T 40002

Perform Function "11 - Login"

Display:

Fig 1: Identifying Scan Tool Display - Basic Setting, Ground Clearances (1 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Press buttons 1 and 1.

Display:

Fig 2: Identifying Scan Tool Display - Basic Setting, Ground Clearances (2 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Confirm input with -Q- button.

Indicated on display:

Fig 3: Identifying Scan Tool Display - Basic Setting, Ground Clearances (3 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Press buttons 3, 1, 5, 6 and 4.

Indicated on display:

Fig 4: Identifying Scan Tool Display - Basic Setting, Ground Clearances (4 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Confirm input with -Q- buttons.

Indicated on display:

Fig 5: Identifying Scan Tool Display - Basic Setting, Ground Clearances (5 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Press buttons 0 and 4.

Display:

Fig 6: Identifying Scan Tool Display - Basic Setting, Ground Clearances (6 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Confirm input with -Q- button.

Indicated on display:

Fig 7: Identifying Scan Tool Display - Basic Setting, Ground Clearances (7 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Press buttons 0, 0, and 1.

Indicated on display

Fig 8: Identifying Scan Tool Display - Basic Setting, Ground Clearances (8 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Confirm input with -Q- button.

Indicated on display:

Fig 9: Identifying Scan Tool Display - Basic Setting, Ground Clearances (9 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Press --> button.

The system vents air and lowers the rear down to special tool T 40002.

At the same time, the control module forgets the old control position. There is an entry into the DTC memory (DTC 01437).

After completion of basic setting, the following appears in display:

Fig 10: Identifying Scan Tool Display - Basic Setting, Ground Clearances (10 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Now press button 3.

Indicated on display:

Fig 11: Identifying Scan Tool Display - Basic Setting, Ground Clearances (11 Of 11)

Courtesy of AUDI OF AMERICA, INC.

Press --> button.
The basic setting procedure is now completed.
Erase DTC memory.
See ON BOARD DIAGNOSTIC (OBD) .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.