Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2004 Volvo V70 Base, 2.4 61, StandardFACTORY OEM SERVICE PROCEDURE
Brake Control Module (BCM) Diagnostic Trouble Code (DTC) Diagnostics
- BCM-0061: Brake Discs. Temperature Too High (2002-2007)
- BCM-0065: Stop Lamp Switch. Faulty Signal (2002-2007)
- BCM-0068: Sensor Power Supply. Faulty Signal (2002-2007)
- BCM-0070: Power Supply For The Pump Motor. Faulty Signal (2002-2007)
- BCM-0071: Pump Motor. Signal Missing (2002-2007)
- BCM-0072: Pump Motor. Mechanical Fault (2002-2007)
- BCM-0074: Hydraulic Valves. Faulty Signal (2002-2007)
- BCM-0076: Control Module. Faulty Configuration (2002-2007)
- Diagnostic trouble code (DTC) information
- Faulty configuration
- Preparation
- Fault-tracing information
- Checking diagnostic trouble codes (DTCs) in the central electronic module (CEM)
- Checking the software
- Erasing diagnostic trouble codes (DTCs)
- Reading off diagnostic trouble codes (DTCs)
- Checking the car configuration
- Checking the brake system
- Resetting and configuring the brake control module (BCM)
- Resetting and configuring the control module
- Information
- Preparation
- BCM-0080: Lateral Accelerometer. Incorrect Offset Value (2002-2007)
- BCM-0081: Accelerometer. Incorrect Offset Value (2002-2007)
- BCM-0082: Yaw Rate Sensor. Incorrect Offset Value (2002-2007)
- BCM-0083: Angle Of Lean Sensor. Incorrect Offset Value (2005-2007)
- BCM-0090: Lateral Accelerometer. Faulty Signal (2002-2007)
- BCM-0091: Accelerometer. Faulty Signal (2002-2007)
- BCM-0092: Yaw Rate Sensor. Faulty Signal (2002-2007)
- BCM-0093: Angle Of Lean Sensor. Faulty Signal (2005-2007)
- BCM-0094: Communication Between Control Units Communication Problems With DEM (2002-2007)
- BCM-0095: Communication Between Control Units Communication Problems With DEM (2002)
- BCM-0095: Communication Between Control Units Communication Problems With DEM (2003-2007)
- BCM-0097: Communication Between Control Modules. Communication Problems With The Central Electronic Module (CEM) (2002-2007)
- BCM-0100: Communication Between Control Modules. Communication Problems With The Engine Control Module (ECM) (2002-2007)
- BCM-0101: Communication Between Control Modules. Communication Problems With The Engine Control Module (ECM) (2002-2007)
- BCM-0103: Pedal Position Sensor. Faulty Signal (2002-2007)
- BCM-0106: Steering Wheel Or Wheel Alignment. Incorrect Steering Wheel Or Wheel Alignment (2002-2007)
- BCM-0108: Communication Between Control Modules. Communication With The Steering Angle Sensor. Control Module Not Initiated (2002-2007)
- BCM-0109: Communication Between Control Modules. Communication With The Steering Angle Sensor. Internal Fault (2002-2004)
- BCM-0109: Communication Between Control Modules. Communication With The Steering Angle Sensor. Internal Fault (2005-2007)
- BCM-0111: Communication Between Control Modules. Check Of The Steering Angle Sensor Tolerances Has Not Been Run (2002-2007)
- BCM-0112: Active Yaw Control Sensor. Sensor Not Calibrated (2002-2007)
- BCM-0113: Back-Up (Reversing) Signal. Signal Missing (2002-2007)
- BCM-0114: Communication With The Active Yaw Control Sensor. Signal Missing (2002-2007)
- BCM-0115: Communication Between Control Modules. Communication With The Steering Angle Sensor. Signal Missing (2002-2007)
- BCM-0116: Communication With The Active Yaw Control Sensor. Communication Problems (2002-2007)
- BCM-0117: Communication With The Active Yaw Control Sensor. An Incorrect Active Yaw Control Sensor Had Been Installed (2002-2007)
- BCM-0118: Power Supply For The Active Yaw Control Sensor. Voltage Too High (2002-2007)
- BCM-0119: Power Supply For The Active Yaw Control Sensor. Voltage Too Low (2002-2007)
- BCM-0121: Yaw Rate Sensor. Signal Outside Its Permitted Range (2002-2007)
- BCM-0123: Active Yaw Control Sensor. Internal Fault (2005-2007)
- BCM-0123: Active Yaw Control Sensor. Internal Fault (2002-2004)
- BCM-0125: Lateral Accelerometer. Signal Outside Its Permitted Range (2002-2007)
- BCM-0127: Angle Of Lean Sensor. Signal Outside Its Permitted Range (2005-2007)
- BCM-0129: Accelerometer. Signal Outside Its Permitted Range (2002-2007)
- BCM-0130: Brake Pressure Sensor 1. Signal Too Low (2002-2007)
- BCM-0133: Brake Pressure Sensor 2. Signal Too Low (2002-2007)
- BCM-0136: Brake Pressure Sensor 1 And 2. Signal Outside Its Permitted Range (2002-2007)
- BCM-0138: Power Supply For The Active Yaw Control Sensor. Faulty Voltage (2002-2007)
- BCM-0139: Pressure Build-Up Valve, Power Brake Booster. Signal Outside Its Permitted Range (2002-2007)
- BCM-0140: Pedal Pressure Sensor. Signal Outside Its Permitted Range (2002-2007)
- BCM-0145: Stability Control. Too Long Stability Control (2002-2007)
- BCM-0146: Factory Test, Dynamic Stability And Traction Control (DSTC). Test Cycle Not Approved (2002-2007)
- BCM-0147: Pedal Position Sensor. Signal Outside Its Permitted Range (2002-2007)
- BCM-0148: Communication Between Control Modules. Faulty Configuration Id (2002-2007)
- BCM-0150: Stop Lamp Switch. Signal Outside Its Permitted Range (2002-2007)
- BCM-0151: Control Module. Internal Memory Fault (2002-2007)
- BCM-A030: Communication Between Control Modules. Steering Angle Sensor. Initialization Check Not Run (2005-2007)
- BCM-A030: Communication Between Control Modules. Steering Angle Sensor. Initialization Check Not Run (2002-2004)
- BCM-A031: Communication Between Control Modules. Steering Angle Sensor. Tolerance Check Not Run (2002-2007)
- BCM-A032: Stability Function. Too Long Stability Control (2003-2007)
- BCM-E000: Control Module Communication. Faulty Communication (2005-2007)
- BCM-E000: Control Module Communication. Faulty Communication (2002-2004)
- BCM-E003: Configuration Fault. Faulty Configuration (2005-2007)
- BCM-E003: Configuration Fault. Faulty Configuration (2002-2004)
- BCM-XXXX: Unknown Diagnostic Trouble Code (DTC) For The Current Control Module Version (2002-2007)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.