Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSVOLKSWAGEN2019ARTEON SEL PREMIUMREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCRUISE CONTROL SYSTEMSADAPTIVE CRUISE CONTROL (ACC) SYSTEM CALIBRATIONADAPTIVE CRUISE CONTROL (ACC)ADAPTIVE CRUISE CONTROL (ACC), CALIBRATINGADAPTIVE CRUISE CONTROL (ACC). CALIBRATING. PASSAT AND PASSAT WAGONCALIBRATION PROCEDURE WITH OR WITHOUT PREVIOUS AXLE ALIGNMENT

2019 Volkswagen Arteon SEL Premium

Calibration procedure with or without previous axle alignment

2019 Volkswagen Arteon SEL PremiumSECTION Calibration procedure with or without previous axle alignment

Position the Setting Device Basic Set - VAS6430/1- at a distance -a- from the centrally positioned ACC Reflector Mirror - Audi - VAS6430/3- to the VW emblem in the radiator grille.
1. a - 120 cm ± 2.5 cm
Remove the VW emblem.
Remove any dirt that may be on the sensor lens.
NOTE: The Setting Device Basic Set - VAS6430/1- must not be moved on the calibration beam.
Adjust the adjusting bolt. Refer to Electrical Equipment Adaptive Cruise Control (ACC) Control Module, Removing and Installing.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Position the front wheel measuring sensors -1- on the calibration beam. -->

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
In area -A-, bring item -2- on the rotary knob into alignment with the marking on the mirror (number 2 on the rotary knob must face the vehicle).

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Level the bubble levels -A and B- on the ACC Reflector Mirror - Audi - VAS6430/3- using the adjusting screws -1, 2 and 3-.
Adjust the mirror -4- via the crank -arrow- so that the laser beam is in the center of the sensor lens.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Position the mirror on the side of the calibration beam so that the laser beam is in the center of the sensor lens -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Level the bubble levels -2- of the sensor -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Turn the precision adjustment screw -5- until the display on the wheel alignment computer is located within the tolerance range.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Level the bubble levels -2- of the sensor -1-.
Using the laser beam -3- on the ACC Reflector Mirror - Audi - VAS6430/3-. check whether the bubble level is level and the laser beam is in the center of the sensor lens.
NOTE: If the laser beam does not meet the sensor lens, the ACC Reflector Mirror - Audi - VAS6430/3- must be aligned again.
On the Vehicle Diagnostic Tester press [[GO TO]] and select the function [[Function/component selection]].
Follow the instructions on the screen to perform the adjustment.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.