SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLKSWAGEN2016CC R-LINE EXECUTIVE, 2.0L ENG VIN NREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 13 (CONTROLS, HOUSING - DIRECT SHIFT GEARBOX 02E)34 CONTROLS, HOUSINGSPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2016 Volkswagen CC R-Line Executive, 2.0L Eng VIN N

Fastener Tightening Specifications

2016 Volkswagen CC R-Line Executive, 2.0L Eng VIN NSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2011 Volkswagen CC and 2010 Volkswagen CC. However, it is still accessible from the selected car via links, so may be relevant.
Component Fastener Size Nm
Bevel Box to Transmission Bolt (2) - 40
Drive Axle Heat Shield to Bevel Box Bolt (2) - 25
Drain Plug to Transmission - 45
Mechatronic Cover Bolt (1) - 10
Oil Filter Housing - 20
Oil Pump Cover Bolt (1) - 8
Overflow Tube to Transmission - 3
Selector Shaft Lever to Selector Shaft Nut - 20
Transmission Oil Cooler to Transmission Bolt - 20 + 90°
Transmission Input Speed and Clutch Oil Temperature Sensor Bolt - 10
Wire Bracket to Mechatronic Cover Nut - 10
Selector Mechanism, through 02.09
Bolt (with Spring) to Selector Mechanism - 3
Selector Housing to Body/Selector Mechanism Nut - 9
Selector Lever Cable Adjustment Bolt - 13
Selector Mechanism to Body Nut - 8
Selector Mechanism, from 03.09
Selector Housing to Body Nut - 8
Selector Lever Cable Adjustment Bolt - 13
Selector Mechanism with Selector Lever and Selector Lever Cable to Body Bolt - 8
(1) Tighten the bolts diagonally and in multiple stages.
(2) R32 models only

Mechatronic Unit Bolt Tightening Sequence and Specification 

Fig 1: Identifying Mounting Bolts
GWWN34-10711Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Install new bolts -1 through 10- hand tight.

-- Tighten the bolts in the specified sequence to 5 Nm + 90° (1/4) additional turn.

Oil Pump Bolt, Variety and Tightening Specification 

All 4 bolts with a flat heads

Fig 2: Identifying Transmission Oil Pump And Fasteners
GWWA37-0671Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Tightening specification: 5 Nm + 90° (1/4) additional turn

3 bolts have a flat head, the upper bolt is countersunk

Fig 3: Bolts With Torque Specifications
GWWN34-10842Courtesy of VOLKSWAGEN UNITED STATES, INC.

Tightening specification:

  • Countersunk bolt: 8 Nm without tightening angle (tighten using special wrench, long reach -T10054-)
  • Flat head bolts: 8 Nm + 90° (1/4) additional turn

Bevel Box to Transmission Bracket Bolt Tightening Sequence and Specification (R32 models only) 

Fig 4: Identifying Bracket For Bevel Box & Bolts
GWWA37-0655Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Install the bolts -1 and 2- by hand.

-- Follow the installation sequence:

  1. Tighten the bolts -1- first to 3 Nm. 
  2. Tighten the bolts -2- to 35 Nm. 
  3. Then, tighten the bolts -1- to 45 Nm. 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.