SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLKSWAGEN2012JETTA TDI, 4D WAGON, STANDARD TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE MECHANICALMECHANICAL2.0L - ENGINE ASSEMBLY - ENGINE CODE(S): CJAA (SPORTWAGEN)10 ENGINE ASSEMBLYDESCRIPTION AND OPERATIONENGINE AND TRANSMISSION MOUNT, ADJUSTING
2012 Volkswagen Jetta TDI, 4D Wagon, Standard Trans

Engine And Transmission Mount, Adjusting

2012 Volkswagen Jetta TDI, 4D Wagon, Standard TransSECTION Engine And Transmission Mount, Adjusting

Special tools and workshop equipment required 

  • Engine Support bridge 10-222 A
  • Engine Support Adapter 10-222 A/3
  • Adapter 10-222 A/13
  • Adapter 10-222 A/18
  • Torque Wrench (5-50 Nm) V.A.G 1331
  • Hose Clip Pliers VAS 6362

Procedure 

WARNING:

When doing any repair work, especially in the engine compartment, pay attention to the following due to clearance issues:

  • Route all lines and wires in their original locations.
  • For example, fuel, hydraulic, Evaporative Emission (EVAP), coolant, refrigerant, brake fluid and vacuum lines.
  • Ensure sufficient clearance to all moving or hot components.

-- Remove the engine cover. Refer to ENGINE COVER .

-- Remove the air filter housing. Refer to AIR FILTER HOUSING .

-- Remove the intake tube between the mass airflow sensor -G70- and intake duct. Loosen the hose clamps using hose clip pliers VAS 6362.

CAUTION:

Electronic components could be destroyed when the battery is disconnected:

  • Follow the required steps when disconnecting the battery.

-- Turn off the ignition and disconnect the ground cable -arrow- from the battery. Refer to Removal and Installation .

Fig 1: Identifying Battery And Ground Cable
GWWA10-10251Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the battery, battery tray bolts -arrows- and tray.

Fig 2: Identifying Battery Holder Bolts
GWWA10-1572Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the auxiliary fuel pump -V393- (the fuel lines remain connected). Refer to Auxiliary Fuel Pump -V393- (IN-LINE ELECTRIC FUEL PUMP) .

Jetta from MY 05 through 10, Jetta SportWagen (US)/Jetta Wagon (Canada) for MY 09 and Jetta SportWagen (US)/Golf Wagon (Canada) from MY 10 

Fig 3: View Of Engine Support bridge Components
GWWM10-0155Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the engine support bridge 10-222 A with the necessary adapters as shown and support the engine in the installed position.

Jetta from MY 11 

Fig 4: View Of Engine Support bridge Components
GWWM10-10011Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Special tools and workshop equipment required 

  • -1- Engine support bridge 10-222 A
  • -2- Engine support bridge T40091/1
  • -3- Adapter 10-222 A/18
  • -4- Engine support Adapter 10-222 A/3
  • -5- Adapter 10-222 A/31-4
  • -6- Adapter 10-222 A/31-3
  • -7- Adapter 10-222 A/31-2
  • -8- Adapter 10-222 A/31-1
  • -9- Adapter 10-222 A/18

-- Install the engine support bridge 10-222 A with the necessary adapters as shown and support the engine in the installed position.

Continuation for all Vehicles 

Fig 5: Identifying Engine Mount Bolts
GWWM10-0150Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.