Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Engine Performance
2010 Volkswagen Routan SSECTION Engine Performance
| CONDITION | POSSIBLE CAUSE | CORRECTION |
|---|---|---|
| ENGINE WILL NOT START | 1. Weak battery. | 1. Test battery. Charge or replace as necessary. Refer to BATTERY CHARGING . |
| 2. Corroded or loose battery connections. | 2. Clean and tighten battery connections. Apply a coat of light mineral grease to terminals. | |
| 3. Faulty starter. | 3. Test starting system. | |
| 4. Faulty coils or control unit. | 4. Test and replace as needed. Refer to appropriate diagnostic information. | |
| 5. Incorrect spark plug gap. | 5. Set gap. | |
| 6. Contamination in fuel system. | 6. Clean system and replace fuel filter. | |
| 7. Faulty fuel pump. | 7. Test fuel pump and replace as needed. Refer to appropriate diagnostic information. | |
| 8. Incorrect engine timing. | 8. Check for a skipped timing belt/chain. | |
| ENGINE STALLS OR IDLES ROUGH | 1. Idle speed too low. | 1. Test minimum air flow. |
| 2. Incorrect fuel mixture. | 2. Refer to appropriate diagnostic information. | |
| . | 3. Intake manifold leakage. | 3. Inspect intake manifold, manifold gasket, and vacuum hoses. |
| 4. Faulty ignition coils. | 4. Test and replace as necessary. Refer to appropriate diagnostic information. | |
| ENGINE LOSS OF POWER | 1. Dirty or incorrectly gapped plugs. | 1. Clean plugs and set gap. |
| 2. Contamination in fuel system. | 2. Clean system and replace fuel filter. | |
| 3. Faulty fuel pump. | 3. Test and replace as necessary. Refer to appropriate diagnostic information. | |
| 4. Incorrect valve timing. | 4. Correct valve timing. | |
| 5. Leaking cylinder head gasket. | 5. Replace cylinder head gasket. | |
| 6. Low compression. | 6. Test compression of each cylinder. | |
| 7. Burned, warped, or pitted valves. | 7. Replace valves. | |
| 8. Plugged or restricted exhaust system. | 8. Perform an exhaust restriction test | |
| 9. Faulty ignition coils. | 9. Test and replace as necessary. | |
| ENGINE MISSES ON ACCELERATION | 1. Dirty or incorrectly gapped spark plugs. | 1. Clean spark plugs and set gap. |
| 2. Contamination in fuel system. | 2. Clean fuel system and replace fuel filter. | |
| 3. Burned, warped, or pitted valves. | 3. Replace valves. | |
| 4. Faulty ignition coils. | 4. Test and replace as necessary. | |
| ENGINE MISSES AT HIGH SPEED | 1. Dirty or incorrect spark plug gap. | 1. Clean spark plugs and set gap. |
| 2. Faulty ignition coils. | 2. Test and replace as necessary. | |
| 3. Dirty fuel injectors. | 3. Test and replace as necessary. | |
| 4. Contamination in fuel system. | 4. Clean system and replace fuel filter. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.