Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLKSWAGEN2001CABRIO GLX (1V7) L4-2.0L (ABA)REPAIR AND DIAGNOSISSTARTING AND CHARGINGBATTERYTESTING AND INSPECTIONCOMPONENT TESTS AND GENERAL DIAGNOSTICSLOAD TESTING
2001 Volkswagen Cabrio GLX (1V7) L4-2.0L (ABA)
Load Testing
2001 Volkswagen Cabrio GLX (1V7) L4-2.0L (ABA)SECTION Load Testing
Load test
The electrolyte specific gravity test in conjunction with the battery load test provides specific information of the battery condition.
Special tools and equipment
Battery tester VAS 1979, VAS 5033, Christie Automotive BT-9000 or equivalent.
Note: It is not necessary to remove the battery when using battery test unit VA81979 or VA 85033. The battery does not need to be disconnected.
Performing battery load test
- Switch ignition off.
- Read battery tester operating instructions.
- Connect tester cable clamps to battery terminals as described in tester operating instructions.
The clamps must make good contact with the battery terminals.
The load current to be applied varies according to battery capacity see battery tester operating instructions or refer to table below.
- Perform battery load test as per battery tester operating instructions and compare test result with table.
A minimum voltage is the result of the load test according to battery capacity.
Table
- If minimum voltage is not reached, replace battery.
Explanation of battery load check: Because of the high load on the battery during this test (high current flow) the battery voltage lowers. If the battery is OK, the voltage value only lowers to the minimum voltage.
If the battery is defective, or has a low charge, the battery voltage quickly drops below the minimum voltage.
This low voltage value remains over a long period and the voltage only increases again slowly after a successful test.
The electrolyte specific gravity test in conjunction with the battery load test provides specific information of the battery condition.
Special tools and equipment
Battery tester VAS 1979, VAS 5033, Christie Automotive BT-9000 or equivalent.
Note: It is not necessary to remove the battery when using battery test unit VA81979 or VA 85033. The battery does not need to be disconnected.
Performing battery load test
- Switch ignition off.
- Read battery tester operating instructions.
- Connect tester cable clamps to battery terminals as described in tester operating instructions.
The clamps must make good contact with the battery terminals.
The load current to be applied varies according to battery capacity see battery tester operating instructions or refer to table below.
- Perform battery load test as per battery tester operating instructions and compare test result with table.
A minimum voltage is the result of the load test according to battery capacity.
Table
- If minimum voltage is not reached, replace battery.
Explanation of battery load check: Because of the high load on the battery during this test (high current flow) the battery voltage lowers. If the battery is OK, the voltage value only lowers to the minimum voltage.
If the battery is defective, or has a low charge, the battery voltage quickly drops below the minimum voltage.
This low voltage value remains over a long period and the voltage only increases again slowly after a successful test.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.