SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2020RAV4 XLE, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 8 (HYBRID BATTERY CONTROL SYSTEM - SERVICE INFORMATION (7 OF 7))COMBINATION SWITCHINSPECTION [11/2018 - ]PROCEDURE
2020 Toyota RAV4 XLE, AWD

Inspection [11/2018 - ]: Procedure

2020 Toyota RAV4 XLE, AWDSECTION Procedure
WARNING: This page is about a different variant/trim than selected.
  1. INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY 
    1. Inspect EV mode switch (Integration Control and Panel Assembly)
      1. Measure the resistance according to the value(s) in the table below.
        GTY930363Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (EV Mode Switch (Integration Control and Panel Assembly))

        Standard Resistance

        Tester Connection Condition Specified Condition
        G32-6 (S) - G32-13 (GND) EV mode switch (integration control and panel assembly) being pushed and held Below 1 Ω
        EV mode switch (integration control and panel assembly) not pushed 10 kΩ or higher

        If the result is not as specified, replace the EV mode switch (integration control and panel assembly).

    2. Inspect NORMAL mode switch (Integration Control and Panel Assembly)
      1. Measure the resistance according to the value(s) in the table below.
        GTY857169Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (NORMAL Mode Switch (Integration Control and Panel Assembly))

        Standard Resistance

        Tester Connection Condition Specified Condition
        G32-8 (B) - G32-13 (GND) NORMAL mode switch (integration control and panel assembly) being pushed and held Below 1 Ω
        NORMAL mode switch (integration control and panel assembly) not pushed 10 kΩ or higher

        If the result is not as specified, replace the NORMAL mode switch (integration control and panel assembly).

    3. Inspect SPORT mode switch (Integration Control and Panel Assembly)
      1. Measure the resistance according to the value(s) in the table below.
        GTY857168Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (SPORT Mode Switch (Integration Control and Panel Assembly))

        Standard Resistance

        Tester Connection Condition Specified Condition
        G32-9 (P) - G32-13 (GND) SPORT mode switch (integration control and panel assembly) being pushed and held Below 1 Ω
        SPORT mode switch (integration control and panel assembly) not pushed 10 kΩ or higher

        If the result is not as specified, replace the SPORT mode switch (integration control and panel assembly).

    4. Inspect the illumination:
      1. Apply battery voltage to the integration control and panel assembly and check that the switch illuminates.

        OK

        Condition Specified Condition
        Battery positive (+) → G32-12 (ILL+)
        Battery negative (-) →G32-1 (ILL-)        		 Illuminates
        GTY857205Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Integration Control and Panel Assembly)

        If the result is not as specified, replace the combination switch.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.