Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Components [12/2021 - ]
2020 Toyota RAV4 XLE, AWDSECTION Components [12/2021 - ]
WARNING: This page is about a different variant/trim than selected.
| Callout | Description | Callout | Description |
|---|---|---|---|
| *A | for Type A | *B | for Type B |
| *C | for Short Type | *D | for Long Type |
| *1 | FRONT FENDER FRONT SPLASH SHIELD LH | *2 | FRONT FENDER FRONT SPLASH SHIELD RH |
| *3 | NO. 1 ENGINE UNDER COVER | *4 | NO. 2 ENGINE UNDER COVER ASSEMBLY |
| *a | Short Type Front Fender Front Splash Shield | *b | Long Type Front Fender Front Splash Shield |
| N.m (kgf/cm, ft.lbf): Specified torque | - | - |
| Callout | Description | Callout | Description |
|---|---|---|---|
| *A | w/ Grille Shutter | - | - |
| *1 | FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY | *2 | NO. 2 FRONT BUMPER ENERGY ABSORBER |
| *3 | RADIATOR SHUTTER SUB-ASSEMBLY | *4 | UPPER RADIATOR AIR GUIDE PLATE |
| N.m (kgf/cm, ft.lbf): Specified torque | - | - |
| *A | w/o Grille Shutter | *B | w/ Grille Shutter |
| *1 | NO. 1 RADIATOR AIR GUIDE LH | *2 | NO. 1 RADIATOR AIR GUIDE RH |
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | HOOD LOCK ASSEMBLY | *2 | INLET AIR CLEANER ASSEMBLY |
| *3 | UPPER RADIATOR SUPPORT SUB-ASSEMBLY | *4 | HOOD LOCK CONTROL CABLE ASSEMBLY |
| N.m (kgf/cm, ft.lbf): Specified torque | MP grease |
| *A | w/o Grille Shutter | *B | w/ Grille Shutter |
| *1 | LOWER RADIATOR SUPPORT | *2 | NO. 1 RADIATOR HOSE |
| *3 | NO. 2 RADIATOR HOSE | *4 | NO. 3 INVERTER COOLING HOSE |
| *5 | NO. 4 INVERTER COOLING HOSE | *6 | NO. 5 INVERTER COOLING HOSE |
| *7 | NO. 5 WATER BY-PASS HOSE | *8 | NO. 6 WATER BY-PASS HOSE |
| *9 | RADIATOR ASSEMBLY | *10 | RADIATOR HOSE SUB-ASSEMBLY |
| *11 | RADIATOR SUPPORT CUSHION | *12 | FAN WITH MOTOR ASSEMBLY |
| *13 | FILLER NECK | *14 | RETAINER |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.