SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2020RAV4 XLE, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 124 (ENGINE LUBRICATION SYSTEM (A25A-FXS) - SERVICE INFORMATION)OIL LEVEL SENSORREMOVAL [11/2018 - ]PROCEDURE
2020 Toyota RAV4 XLE, AWD

Removal [11/2018 - ]: Procedure

2020 Toyota RAV4 XLE, AWDSECTION Procedure
WARNING: This page is about a different variant/trim than selected.
  1. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 13 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 13 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 13 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 13 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 13 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 13 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 13 [10/2023 - ]

  2. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 14 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 14 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 14 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 14 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 14 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 14 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 14 [10/2023 - ]

  3. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 15 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 15 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 15 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 15 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 15 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 15 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 15 [10/2023 - ]

  4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 16 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 16 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 16 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 16 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 16 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 16 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 16 [10/2023 - ]

  5. DRAIN ENGINE OIL 

    Refer to PROCEDURE - Step 2 [11/2018 - 08/2020] , or refer to PROCEDURE - Step 2 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 2 [12/2021 - 10/2023] , or refer to PROCEDURE - Step 2 [10/2023 - ]

  6. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 55 [11/2018 - 06/2020] , or refer to PROCEDURE - Step 55 [06/2020 - 11/2024] , or refer to PROCEDURE - Step 55 [11/2024 - ]

  7. REMOVE ENGINE OIL LEVEL SENSOR 
    1. Disconnect the engine oil level sensor connector.
    2. Remove the clip from the engine oil level sensor.
      GTY771692Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using an 8 mm socket wrench, remove the 2 bolts and engine oil level sensor from engine balancer assembly.
      GTY754900Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.