Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Section 118 (Engine Control System (A25A-FXS) (W/ Canister Pump Module) - Diagnostic Codes (01 Of 13))
2020 Toyota RAV4 XLE, AWDSECTION Section 118 (Engine Control System (A25A-FXS) (W/ Canister Pump Module) - Diagnostic Codes (01 Of 13))
WARNING: This page is about a different variant/trim than selected.
- SFI SYSTEM (w/ Canister Pump Module)
- Vehicle Control History [02/2019 - 06/2020]
- Vehicle Control History [06/2020 - 08/2020]
- DTC P0010-01: Camshaft Position "A" Actuator Bank 1 General Electrical Failure [02/2019 - 06/2020]
- DTC P0010-01: Camshaft Position "A" Actuator Bank 1 General Electrical Failure [06/2020 - 08/2020]
- DTC P0011-00: Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 [02/2019 - 06/2020]
- DTC P0011-00: Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 [06/2020 - 08/2020]
- DTC P0012-00: Camshaft Position "A" - Timing Over-Retarded Bank 1 [02/2019 - 06/2020]
- DTC P0012-00: Camshaft Position "A" - Timing Over-Retarded Bank 1 [06/2020 - 08/2020]
- DTC P0013-13: Camshaft Position "B" - Actuator Bank 1 Circuit Open [02/2019 - 06/2020]
- DTC P0013-13: Camshaft Position "B" - Actuator Bank 1 Circuit Open [06/2020 - 08/2020]
- DTC P0014-00: Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1; DTC P0015-00: Camshaft Position "B" - Timing Over-Retarded Bank 1 [02/2019 - 06/2020]
- DTC P0014-00: Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1; DTC P0015-00: Camshaft Position "B" - Timing Over-Retarded Bank 1 [06/2020 - 08/2020]
- DTC P0016-00: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A [02/2019 - 10/2019]
- DTC P0016-00: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A [10/2019 - 06/2020]
- DTC P0016-00: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A [06/2020 - 08/2020]
- DTC P0017-00: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B [02/2019 - 06/2020]
- DTC P0017-00: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B [06/2020 - 08/2020]
- DTC P0030-12: HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery; DTC P0030-13: HO2S Heater Control Bank 1 Sensor 1 Circuit Open; DTC P101A-9E: A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On [02/2019 - 06/2020]
- DTC P0030-12: HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery; DTC P0030-13: HO2S Heater Control Bank 1 Sensor 1 Circuit Open; DTC P101A-9E: A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On [06/2020 - 08/2020]
- DTC P0036-12: HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery; DTC P0036-13: A/F (O2) Heater Control Circuit Bank 1 Sensor 2 Circuit Open; DTC P102A-9E: O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On [02/2019 - 06/2020]
- DTC P0036-12: HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery; DTC P0036-13: A/F (O2) Heater Control Circuit Bank 1 Sensor 2 Circuit Open; DTC P102A-9E: O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On [06/2020 - 08/2020]
- DTC P0069-00: Manifold Absolute Pressure - Barometric Pressure Correlation [02/2019 - 06/2020]
- DTC P0069-00: Manifold Absolute Pressure - Barometric Pressure Correlation [06/2020 - 08/2020]
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.