Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2019CAMRY XLE, 2.5L ENG VIN 1REPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROL SYSTEM (A25A-FKS) - DIAGNOSTIC CODES (09 OF 17) (EXCEPT HYBRID)
2019 Toyota Camry XLE, 2.5L Eng VIN 1
Engine Control System (A25A-FKS) - Diagnostic Codes (09 Of 17) (Except Hybrid)
2019 Toyota Camry XLE, 2.5L Eng VIN 1SECTION Engine Control System (A25A-FKS) - Diagnostic Codes (09 Of 17) (Except Hybrid)
- SFI System
- DTC P0455-00: Evaporative Emission System Leak Detected (Large Leak); DTC P0456-00: Evaporative Emission System Leak Detected (Very Small Leak) [03/2017 - 06/2017]
- DTC P0455-00: Evaporative Emission System Leak Detected (Large Leak); DTC P0456-00: Evaporative Emission System Leak Detected (Very Small Leak) [06/2017 - 08/2018]
- DTC P0455-00: Evaporative Emission System Leak Detected (Large Leak); DTC P0456-00: Evaporative Emission System Leak Detected (Very Small Leak) [08/2018 - ]
- DTC P0460-12: Fuel Level Sensor "A" Circuit Short to Battery; DTC P0460-14: Fuel Level Sensor "A" Circuit Short to Ground or Open [08/2018 - 03/2020]
- DTC P0460-12: Fuel Level Sensor "A" Circuit Short to Battery; DTC P0460-14: Fuel Level Sensor "A" Circuit Short to Ground or Open [03/2020 - ]
- DTC P0460-2A: Fuel Level Sensor "A" Signal Stuck In Range [08/2018 - 03/2020]
- DTC P0460-2A: Fuel Level Sensor "A" Signal Stuck In Range [03/2020 - 08/2021]
- DTC P0460-2A: Fuel Level Sensor "A" Signal Stuck In Range [08/2021 - ]
- DTC P0500-31: Vehicle Speed Sensor "A" No Signal [03/2017 - 06/2017]
- DTC P0500-31: Vehicle Speed Sensor "A" No Signal [06/2017 - ]
- DTC P0504-2B: Brake Switch "A"/"B" Signal Cross Coupled [03/2017 - 06/2017]
- DTC P0504-2B: Brake Switch "A"/"B" Signal Cross Coupled [06/2017 - 10/2020]
- DTC P0504-2B: Brake Switch "A"/"B" Signal Cross Coupled [10/2020 - 08/2021]
- DTC P0504-2B: Brake Switch "A"/"B" Signal Cross Coupled [08/2021 - ]
- DTC P0505-00: Idle Control System [03/2017 - 06/2017]
- DTC P0505-00: Idle Control System [06/2017 - 08/2018]
- DTC P0505-00: Idle Control System [08/2018 - ]
- DTC P050A-00: Cold Start Idle Control System Performance [03/2017 - 06/2017]
- DTC P050A-00: Cold Start Idle Control System Performance [06/2017 - 08/2018]
- DTC P050A-00: Cold Start Idle Control System Performance [08/2018 - ]
- DTC P050B-00: Cold Start Ignition Timing Performance [03/2017 - 06/2017]
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.