SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2013SEQUOIA LIMITED, 5.7L ENG VIN WREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTWARNING SYSTEMSINTUITIVE PARKING ASSIST SYSTEM (DIAGNOSTICS & CIRCUIT TESTS)INTUITIVE PARKING ASSIST SYSTEMCIRCUIT TESTSPARK / NEUTRAL POSITION SWITCH CIRCUITPROCEDURE
2013 Toyota Sequoia Limited, 5.7L Eng VIN W

Park / Neutral Position Switch Circuit: Procedure

2013 Toyota Sequoia Limited, 5.7L Eng VIN WSECTION Procedure
  1. INSPECT PARK / NEUTRAL POSITION SWITCH 
    1. Disconnect the D21 park/neutral position switch connector.
      Fig 1: Measuring Resistance Of Park/Neutral Position Switch Connector
      GTY223789Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Condition Condition Specified Condition
      6 (PL) - 2 (RB) Shift lever in P Below 1 Ω
      1 (RL) - 2 (RB) Shift lever in R Below 1 Ω
      6 (PL) - 2 (RB) Shift lever not in P 10 kΩ or higher
      1 (RL) - 2 (RB) Shift lever not in R 10 kΩ or higher
      RESULT

      Result Proceed to
      OK A
      NG (for AB60E) B
      NG (for AB60F) C

    B → See step   4 

    C → See step   5 

    A: Go to next step 

  2. CHECK HARNESS AND CONNECTOR (SWITCH - CLEARANCE WARNING ECU - BATTERY AND BODY GROUND) 
    1. Disconnect the D21 park/neutral position switch connector.
      Fig 2: Measuring Voltage Of Park/Neutral Position Switch & Clearance Warning ECU Harness & Connectors
      GTY240457Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the H43 clearance warning ECU connector.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Condition Switch Condition Specified Condition
      D21-2 (RB) - Body ground Ignition switch ON 11 to 14 V
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Condition Condition Specified Condition
      D21-6 (PL) - H43-1 (PL) Always Below 1 Ω
      D21-1 (RL) - H43-13 (RL)
      D21-6 (PL) - Body ground Always 10 kΩ or higher
      D21-1 (RL) - Body ground

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → See step   3 

  3. PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE  
  4. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY. Refer to  REMOVAL 
  5. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY. Refer to  REMOVAL 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.