Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2011LANDCRUISER V8-5.7L (3UR-FE)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSVARIABLE VALVE TIMING ACTUATORSERVICE AND REPAIRINSTALLATION
2011 Toyota Landcruiser V8-5.7L (3UR-FE)
Installation
2011 Toyota Landcruiser V8-5.7L (3UR-FE)SECTION Installation
3UR-FE ENGINE CONTROL: CAMSHAFT OIL CONTROL VALVE: INSTALLATION
1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)
(a) Install a new O-ring to the oil control valve.
(b) Apply a light coat of engine oil to the O-ring.
(c) Install the oil control valve with the bolt.
Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)
NOTICE:
* Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
* Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
(d) Connect the oil control valve connector.
2. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1)
(a) Install a new O-ring to the oil control valve.
(b) Apply a light coat of engine oil to the O-ring.
(c) Install the oil control valve with the bolt.
Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)
NOTICE:
* Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
* Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
(d) Connect the oil control valve connector.
3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2)
(a) Install a new O-ring to the oil control valve.
(b) Apply a light coat of engine oil to the O-ring.
(c) Install the oil control valve with the bolt.
Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)
NOTICE:
* Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
* Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
(d) Connect the oil control valve connector.
4. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)
(a) Install a new O-ring to the oil control valve.
(b) Apply a light coat of engine oil to the O-ring.
(c) Install the oil control valve with the bolt.
Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)
NOTICE:
* Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
* Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.
(d) Connect the oil control valve connector.
5. INSTALL AIR CLEANER HOSE ASSEMBLY Installation
6. INSTALL V-BANK COVER SUB-ASSEMBLY Installation
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.