Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2011FJ CRUISER 2WD V6-4.0L (1GR-FE)REPAIR AND DIAGNOSISRESTRAINTS AND SAFETY SYSTEMSRELAYS AND MODULES - RESTRAINTS AND SAFETY SYSTEMSAIR BAG CONTROL MODULESERVICE AND REPAIRINSTALLATION
2011 Toyota FJ Cruiser 2WD V6-4.0L (1GR-FE)
Installation
2011 Toyota FJ Cruiser 2WD V6-4.0L (1GR-FE)SECTION Installation
SUPPLEMENTAL RESTRAINT SYSTEM: CENTER AIRBAG SENSOR ASSEMBLY: INSTALLATION
1. PRECAUTION
CAUTION:
Read "PRECAUTION" thoroughly before servicing Service Precautions.
2. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
(a) Check that the ignition switch is turned to OFF.
(b) Check that the negative (-) battery terminal is disconnected.
NOTICE:
After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.
(c) Temporarily install the center airbag sensor assembly with the 3 bolts.
NOTICE:
* If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
* When installing the center airbag sensor assembly, make sure that the SRS wiring does not interfere with any other parts and that it is not pinched between other parts.
(d) Tighten the 3 bolts to the specified torque.
Torque : 17.5 Nm (179 kgf-cm, 13 ft-lbf)
(e) Check that there is no looseness in the installation parts of the center airbag sensor assembly.
(f) Connect the holder (with connectors) to the center airbag sensor assembly.
(g) Check that the water-proof sheet is properly set.
3. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY Installation
4. INSTALL CONSOLE UPPER PANEL NO.1 GARNISH Installation
5. INSTALL FRONT CONSOLE BOX Installation
6. INSTALL BOX BOTTOM MAT Installation
7. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY Installation
8. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY Installation
9. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) Installation
10. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD) Installation
11. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY Installation
12. INSTALL INSTRUMENT PANEL GARNISH RH Installation
13. INSTALL INSTRUMENT PANEL GARNISH LH Installation
14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque : 3.9 Nm (40 kgf-cm, 35 in-lbf)
15. PERFORM INITIALIZATION
(a) Perform initialization Repair Instruction - Initialization.
HINT
Some systems need initialization after reconnecting the cable to the negative battery terminal.
16. INSPECT SRS WARNING LIGHT
(a) Inspect the SRS warning light Diagnosis System.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.