Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2011FJ CRUISER 2WD V6-4.0L (1GR-FE)REPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - ACCESSORIES AND OPTIONAL EQUIPMENTPARKING ASSIST CONTROL MODULESERVICE AND REPAIRINSTALLATION
2011 Toyota FJ Cruiser 2WD V6-4.0L (1GR-FE)
Installation
2011 Toyota FJ Cruiser 2WD V6-4.0L (1GR-FE)SECTION Installation
PARK ASSIST / MONITORING: CLEARANCE WARNING ECU: INSTALLATION
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing Service Precautions.
1. INSTALL CLEARANCE WARNING ECU ASSEMBLY
(a) Insert the hook into the instrument panel reinforcement hole and install the clearance warning ECU with the nut.
Torque : 12.5 Nm (125 kgf-cm, 9 ft-lbf)
(b) Connect the clearance warning ECU connector.
2. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY Installation
3. CONNECT PASSENGER AIRBAG CONNECTOR Installation
4. INSTALL INSTRUMENT PANEL FINISH PANEL END Installation
5. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY Installation
6. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY RH Installation
7. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY LH Installation
8. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY RH Installation
9. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH Installation
10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation
11. INSTALL COMBINATION METER ASSEMBLY Installation
12. INSTALL INSTRUMENT CLUSTER LOWER FINISH PANEL Installation
13. INSTALL INSTRUMENT LOWER PANEL Installation
14. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY LH Installation
15. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY Installation
16. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY LH Installation
17. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY Installation
18. INSTALL FRONT CONSOLE BOX UPPER PANEL GARNISH Installation
19. INSTALL FRONT CONSOLE BOX Installation
20. INSTALL FRONT CONSOLE BOX BOTTOM MAT Installation
21. INSTALL FRONT CONSOLE BOX UPPER PANEL SUB-ASSEMBLY Installation
22. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD) Installation
23. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission) Installation
24. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY Installation
25. INSTALL RADIO RECEIVER ASSEMBLY Installation
26. INSTALL INTEGRATION CONTROL PANEL ASSEMBLY Installation
27. INSTALL INSTRUMENT PANEL GARNISH LH Installation
28. INSTALL INSTRUMENT PANEL GARNISH RH Installation
29. INSTALL ASSIST GRIP RETAINER RH Installation
30. INSTALL ASSIST GRIP RETAINER LH Installation
31. INSTALL FRONT PILLAR GARNISH RH Installation
32. INSTALL FRONT PILLAR GARNISH LH Installation
33. INSTALL ASSIST GRIP ASSEMBLY Installation
34. INSTALL ASSIST GRIP PLUG Installation
35. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH Installation
36. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH Installation
37. INSTALL COWL SIDE TRIM BOARD RH Installation
38. INSTALL COWL SIDE TRIM BOARD LH Installation
39. INSTALL FOOTREST CLIP Installation
40. INSTALL FRONT FLOOR FOOTREST Installation
41. INSTALL FRONT DOOR SCUFF PLATE RH Installation
42. INSTALL FRONT DOOR SCUFF PLATE LH Installation
43. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque : 3.9 Nm (40 kgf-cm, 35 in-lbf)
44. INSPECT SRS WARNING LIGHT
Diagnosis System
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.