Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSTOYOTA2009YARIS S, 4D HATCHBACKREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCEENGINE CONTROL SYSTEM (1NZ-FE)SFI SYSTEMDTC P0606 ECM/PCM PROCESSORINSPECTION PROCEDURE

2009 Toyota Yaris S, 4D Hatchback

Inspection Procedure

2009 Toyota Yaris S, 4D HatchbackSECTION Inspection Procedure

CHECK ANY OTHER DTCS OUTPUT

Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the tester ON.
Select the following menu items: Powertrain/Engine and ECT/Trouble Codes.

Read the DTCs.

Result

RESULT REFERENCE

Result	Proceed to
P0606 and P0136, P0137 or P0138	A
P0606	B

B: Go to step 3

A: Go to next step

CHECK DTC (P0136, P0137 OR P0138)
1. Check the P0136, P0137 or P0138 flow chart.
  HINT:
  - If P0136 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2) ). Then proceed to step 6.
  - If P0137 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2) ). Then proceed to step 6.
  - If P0138 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2) ). Then proceed to step 6.
  - If DTC P0606 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).
    NEXT: Go to step 6
CHECK FOR EXHAUST GAS LEAK
1. Allow the engine to idle and rev the engine.
2. Check for exhaust gas leaks around the heated oxygen sensor.
  If any exhaust gas leaks are present, repair it and proceed to step 4. If no exhaust gas leaks are present, proceed to step 4.
  
  HINT:
  - If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.
  - If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.

PERFORM CONFIRMATION DRIVING PATTERN

Clear the DTC (See DTC CHECK/CLEAR ).
Connect the Techstream to the DLC3.
Warm up the engine until the engine coolant temperature becomes 75° (167°F) or more.
Perform the driving pattern.

Fig 1: Driving Pattern Of Engine Coolant Temperature
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Accelerate the vehicle until 50 mph (80 km/h) and stop the vehicle.
2. Drive the vehicle by 35 to 50 mph (60 to 80 km/h) for 5 minutes or more.
Select the following menu items: Powertrain/Engine and ECT/Trouble Codes.

Read the DTCs.

Result

RESULT REFERENCE

Result	Proceed to
P0606 and P0136, P0137 or P0138	A
P0606	B
No output	C

B: REPLACE ECM (See REMOVAL )

C: Go to step 6

A: Go to next step

CHECK DTC (P0136, P0137 OR P0138)
1. Check the P0136, P0137 or P0138 flow chart.
  HINT:
  - If P0136 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2) ). Then proceed to step 6.
  - If P0137 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2) ). Then proceed to step 6.
  - If P0138 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2) ). Then proceed to step 6.
  - If DTC P0606 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).

INSPECT ECM

Clear the DTC (See DTC CHECK/CLEAR ).
Stop the engine and wait for 30 minutes.
Connect the Techstream to the DLC3.
Start the engine and allow it to idle for 2 minutes.
Turn the tester ON.
Select the following menu items: Powertrain/Engine and ECT/Trouble Codes.

Read the DTCs.

Result

RESULT REFERENCE

Result	Proceed to
P0606	A
No output	B

B: END

A: REPLACE ECM (See REMOVAL )

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.