SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2009YARIS BASE, 4D SEDAN, AUTOMATICREPAIR AND DIAGNOSISBRAKESTRACTION CONTROLBRAKE CONTROLANTI-LOCK BRAKE SYSTEM (FOR HATCHBACK)DATA LIST/ACTIVE TEST
2009 Toyota Yaris Base, 4D Sedan, Automatic

Data List/Active Test

2009 Toyota Yaris Base, 4D Sedan, AutomaticSECTION Data List/Active Test
  1. DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the tester on.
    6. Enter the following menus: Chassis/ABS/VSC/TRC/Data List.
    7. According to the display on the tester, read the Data List.

      ABS/VSC/TRC 

      ABS/VSC/TRC - DATA LIST

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ABS Warning Light ABS warning light/ON or OFF ON: Warning light ON
      OFF: Warning light OFF      		 -
      Brake Warning Light Brake warning light/ON or OFF ON: Warning light ON
      OFF: Warning light OFF      		 -
      Stop Light SW Stop light switch/ON or OFF ON: Brake pedal depressed
      OFF: Brake pedal released      		 -
      Parking Brake SW Parking brake switch/ON or OFF ON: Parking brake applied
      OFF: Parking brake released      		 -
      Deceleration Sensor Acceleration sensor 1 reading/min.: -18.52 G, max.: 18.39 G Approximately -0.13 to 0.13 G while stationary Reading changes when vehicle is bounced
      Forward and Rearward G Forward and rearward G/min.: -25.11 m/sec.2 , max.: 24.91 m/sec.2 Min.:-25.11 m/sec.2
      Max.: 24.91 m/sec.2      		 -
      FR Wheel Speed FR wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      FL Wheel Speed FL wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      RR Wheel Speed RR wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      RL Wheel Speed RL wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      Vehicle Speed Maximum wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual vehicle speed Speed indicated on speedometer
      FR Wheel Acceleration FR wheel acceleration/Min.: -200.84 m/s2 , Max.: 199.27 m/s2 0 m/s2 -
      FL Wheel Acceleration FL wheel acceleration/Min.: -200.84 m/s2 , Max.: 199.27 m/s2 0 m/s2 -
      RR Wheel Acceleration RR wheel acceleration/Min.: -200.84 m/s2 , Max.: 199.27 m/s2 0 m/s2 -
      RL Wheel Acceleration RL wheel acceleration/Min.: -200.84 m/s2 , Max.: 199.27 m/s2 0 m/s2 -
      FR Wheel ABS Ctrl Status FR wheel ABS control status/ON or OFF ON: During the control -
      FL Wheel ABS Ctrl Status FL wheel ABS control status/ON or OFF ON: During the control -
      RR Wheel ABS Ctrl Status RR wheel ABS control status/ON or OFF ON: During the control -
      RL Wheel ABS Ctrl Status RL wheel ABS control status/ON or OFF ON: During the control -
      RR Wheel EBD Ctrl Status RR wheel EBD control status/ON or OFF ON: During the control -
      RL Wheel EBD Ctrl Status RL wheel EBD control status/ON or OFF ON: During the control -
      Solenoid Relay ABS solenoid relay/ON or OFF ON: Solenoid relay ON
      OFF: Solenoid relay OFF      		 -
      ECB (Electronically Controlled Brake system) Motor Relay ABS motor relay/ON or OFF ON: Motor relay ON
      OFF: Motor relay OFF      		 -
      ABS Solenoid (SFRH) ABS solenoid (SFRH)/ON or OFF ON: Operates -
      ABS Solenoid (SFRR) ABS solenoid (SFRR)/ON or OFF ON: Operates -
      ABS Solenoid (SFLH) ABS solenoid (SFLH)/ON or OFF ON: Operates -
      ABS Solenoid (SFLR) ABS solenoid (SFLR)/ON or OFF ON: Operates -
      ABS Solenoid (SRRH) ABS solenoid (SRRH)/ON or OFF ON: Operates -
      ABS Solenoid (SRRR) ABS solenoid (SRRR)/ON or OFF ON: Operates -
      ABS Solenoid (SRLH) ABS solenoid (SRLH)/ON or OFF ON: Operates -
      ABS Solenoid (SRLR) ABS solenoid (SRLR)/ON or OFF ON: Operates -
      FR Speed Open FR speed sensor open detection/Error or Normal Error: Momentary interruption
      Normal: Normal      		 -
      FL Speed Open FL speed sensor open detection/Error or Normal Error: Momentary interruption
      Normal: Normal      		 -
      RR Speed Open RR speed sensor open detection/Error or Normal Error: Momentary interruption
      Normal: Normal      		 -
      RL Speed Open RL speed sensor open detection/Error or Normal Error: Momentary interruption
      Normal: Normal      		 -
      Number of DTC Number of DTC recorded/Min.: 0, Max.: 255 Min.: 0
      Max.: 255      		 -
  2. ACTIVE TEST 

    HINT:

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the tester on.
    6. Enter the following menus: Chassis/ABS/VSC/ TRC/Active Test.
    7. According to the display on the tester, perform the Active Test.

      ABS/VSC/TRC 

      ABS/VSC/TRC - DATA LIST

      Tester Display Test Part Control Range Diagnostic Note
      ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter
      Brake Warning Light Brake warning light Warning light ON/OFF Observe combination meter
      Solenoid Relay ABS solenoid relay Relay ON/OFF -
      Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard
      ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRRR) ABS solenoid (SRRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.