Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2009VENZA AWD V6-3.5L (2GR-FE)REPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINETIMING COMPONENTSSYSTEM SPECIFICATIONS
2009 Toyota Venza AWD V6-3.5L (2GR-FE)
System Specifications
2009 Toyota Venza AWD V6-3.5L (2GR-FE)SECTION System Specifications
NO. 1 CHAIN TENSIONER ASSEMBLY
Install the No. 1 chain tensioner assembly with the 2 bolts.
Torque 10 Nm (102 kgf-cm, 7ft-lbf)
NO. 3 CHAIN TENSIONER ASSEMBLY
Install the No. 3 chain tensioner assembly with the bolt.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
NO. 2 CHAIN TENSIONER ASSEMBLY
Install the No. 2 chain tensioner assembly with the bolt.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
TIMING CHAIN COVER SUB-ASSEMBLY
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
Bolt Length
Make sure that there is no oil on the threads of bolt B and C.
Fully tighten the bolts in area 1 and area 2.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
Fully tighten the bolts and nuts in area 3.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
Tighten the bolts and nuts from top to bottom as shown in the illustration.
Fully tighten the bolts in area 4.
Bolt A - Torque 43 Nm (438 kgf-cm, 32ft-lbf)
Except bolt A - Torque 21 Nm (214 kgf-cm, 15ft-lbf)
Tighten the bolts from bottom to top as shown in the illustration.
CRANKSHAFT PULLEY
Torque 250 Nm (2550 kgf-cm, 184ft-lbf)
Install the No. 1 chain tensioner assembly with the 2 bolts.
Torque 10 Nm (102 kgf-cm, 7ft-lbf)
NO. 3 CHAIN TENSIONER ASSEMBLY
Install the No. 3 chain tensioner assembly with the bolt.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
NO. 2 CHAIN TENSIONER ASSEMBLY
Install the No. 2 chain tensioner assembly with the bolt.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
TIMING CHAIN COVER SUB-ASSEMBLY
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
Bolt Length
Make sure that there is no oil on the threads of bolt B and C.
Fully tighten the bolts in area 1 and area 2.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
Fully tighten the bolts and nuts in area 3.
Torque 21 Nm (214 kgf-cm, 15ft-lbf)
Tighten the bolts and nuts from top to bottom as shown in the illustration.
Fully tighten the bolts in area 4.
Bolt A - Torque 43 Nm (438 kgf-cm, 32ft-lbf)
Except bolt A - Torque 21 Nm (214 kgf-cm, 15ft-lbf)
Tighten the bolts from bottom to top as shown in the illustration.
CRANKSHAFT PULLEY
Torque 250 Nm (2550 kgf-cm, 184ft-lbf)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.