SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2009CAMRY HYBRIDREPAIR AND DIAGNOSISBODY & FRAMEDOOR LOCKSDOOR LOCK (HYBRID)SMART KEY SYSTEMCUSTOMIZE PARAMETERS
2009 Toyota Camry Hybrid

Customize Parameters

2009 Toyota Camry HybridSECTION Customize Parameters
  1. CUSTOMIZING FUNCTION WITH TECHSTREAM 

    HINT:

    The items in the table below can be customized.

    NOTE:
    • When the customer requests a change in a function, first make sure that the function can be customized.
    • Be sure to make a note of the current setting before customizing.
    • When troubleshooting a function, first make sure that the function is set to the default setting.
    1. Connect Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the tester on.
    4. Enter the following menus: Customize Setting / Smart Key.
    5. Select the setting by referring to the table below.

    Smart: 

    FUNCTION CHART

    Tester Display Default Contents Setting
    Park Wait Time (Wait time to permit opening door after locking) 2.5s Function that sets waiting time to permit opening door after door is locked with entry lock function. 0.5s/1.5s/2.5s/ 5.0s
    Ignition Available Area (SMART ignition available area) ALL Function to choose the available area for electrical key to start HV control system and cancel the steering lock. FRONT/ALL
    Trunk Open Mode (Luggage compartment opening operation) ON Function to open a luggage compartment when the driver has the electrical key and presses the luggage open button. ON / OFF

    Wireless Door Lock: 

    FUNCTION CHART

    Display (Item) Default Contents Setting
    Alarm Function (Panic function) ON Function to operate the theft deterrent system by keeping pressing the lock button of the transmitter for 2.5 seconds. If there is a panic button, press the panic button instead of the lock button. ON / OFF

    Warning: 

    FUNCTION CHART

    Display (Item) Default Contents Setting
    Key Low-Batt Wrn ON Function to set a warning function for the time when a key battery becomes weak. ON / OFF
  2. CUSTOMIZING FUNCTION WITHOUT TECHSTREAM (Entry Unlock Mode Switching Function) 
    1. To change the vehicle to entry unlock mode switching function, make sure the vehicle power is off and simultaneously press and hold the electrical key's LOCK switch and another electrical key switch for 4.5 seconds.

      When the switches are pressed and held for 4.5 seconds, the entry door unlock mode changes in the following order: driver door mode, all door mode.

      NOTE: After pressing and holding the switches for 4.5 seconds, wait 4.5 seconds before performing the same procedure again.
      • Driver door unlock mode:

        When the driver door's touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

      • All door unlock mode:

        When the touch sensor is touched, all doors unlock.

    2. The certification ECU receives this signal from the door control receiver and changes the smart key system to the entry unlock mode.
    3. The certification ECU sounds the buzzers of the wireless door lock buzzer and combination meter to inform the user that the mode has been switched.
    Fig 1: Multi-Information Display
    G04972366Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    The function only changes the entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.

  3. CUSTOMIZING FUNCTION WITHOUT TECHSTREAM (Electrical Key Cancel) 

    The electrical key cancel operation disables the following functions:

    • Entry Unlock/Lock
    • Entry Luggage Compartment Open
    • Electrical Key Lock-in Prevention
    • Warning
    • Memory Call

    The operation procedures are as follows: Precondition:

    Power switch off, driver side door closed and unlocked.

    1. Unlock the driver side door once with the UNLOCK switch of the electrical key.
    2. Open the driver door within 5 seconds.
    3. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.
    4. Repeat open → close twice for the driver door within 30 seconds, and open again.

      (Driver door: Open → Close → Open → Close → Open)

    5. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.
    6. Repeat open → close once for the driver door within 30 seconds, and open again.

      (Driver door: Open → Close → Open)

    7. Close the driver door within 5 seconds.

      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

      To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.