Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA20084 RUNNER 2WD V8-4.7L (2UZ-FE)REPAIR AND DIAGNOSISBODY AND FRAMESEATSSERVICE AND REPAIRREAR NO. 1 SEAT ASSEMBLYREASSEMBLY
2008 Toyota 4 Runner 2WD V8-4.7L (2UZ-FE)
Reassembly
2008 Toyota 4 Runner 2WD V8-4.7L (2UZ-FE)SECTION Reassembly
SEAT: REAR NO. 1 SEAT ASSEMBLY: REASSEMBLY
SEAT: REAR NO. 1 SEAT ASSEMBLY: REASSEMBLY
1. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH
(a) Install the seat cushion cover to the seat cushion pad with new hog rings.
(b) Install the seat cushion cover with the pad to the seat cushion frame with new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
2. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH
HINT: Use the same procedures described for the LH side.
3. INSTALL REAR SEAT CUSHION UNDER COVER LH
(a) Install the under cover with the 5 clips.
4. INSTALL REAR SEAT CUSHION UNDER COVER RH
(a) Install the under cover with the 7 clips.
5. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH
(a) Install the seatback cover to the seatback pad RH with new hog rings.
(b) Install the seatback cover with the pad to the seatback frame with new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
6. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH
HINT: Use the same procedures described for the LH side.
7. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
(a) Install the 2 hinge with the 2 bolts.
Torque: 18 Nm (184 kgf-cm, 13 ft-lbf)
8. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
9. INSTALL REAR SEAT BELT OUTER CENTER
(a) Install the belt with the nut.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
10. INSTALL REAR SEAT ARMREST ASSEMBLY CENTER
(a) Install the armrest with the bolt.
Torque: 8.0 Nm (82 kgf-cm, 71 in-lbf)
(b) Install the armrest cover with the screw.
11. INSTALL REAR SEAT LOCK STRIKER SUB-ASSEMBLY
(a) Install the 2 strikers with the 6 bolts.
Torque: 18 Nm (184 kgf-cm, 13 ft-lbf)
12. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY CENTER
(a) Install the hinge with the 2 bolts.
Torque: 18 Nm (184 kgf-cm, 13 ft-lbf)
13. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH
(a) Install the hinge with the bolt.
Torque: 18 Nm (184 kgf-cm, 13 ft-lbf)
14. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.