Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2007HIGHLANDER 4WD L4-2.4L (2AZ-FE)REPAIR AND DIAGNOSISMAINTENANCEDRIVE BELTSERVICE AND REPAIR
2007 Toyota Highlander 4WD L4-2.4L (2AZ-FE)
Drive Belt: Service and Repair
2007 Toyota Highlander 4WD L4-2.4L (2AZ-FE)SECTION Service and Repair
DRIVE BELT
REMOVAL
1. REMOVE FRONT WHEEL RH
2. REMOVE FRONT FENDER SPLASH SHIELD FRONT RH
3. REMOVE FRONT FENDER APRON SEAL RH
4. REMOVE ENGINE MOUNTING STAY NO.2 RH
5. REMOVE ENGINE COVER SUB-ASSEMBLY NO.1
6. REMOVE ENGINE MOVING CONTROL ROD W/BRACKET
7. REMOVE ENGINE MOUNTING BRACKET NO.2 RH
8. REMOVE FAN AND GENERATOR V BELT
(a) Slowly turn the belt tensioner clockwise for more than 3 seconds, and remove the drive belt by using SST.
SST 09843-18030
INSTALLATION
1. INSTALL FAN AND GENERATOR V BELT
(a) Slowly turn the belt tensioner clockwise for more than 3 seconds, and install the drive belt by using SST.
SST 09249-63010
2. INSTALL ENGINE MOUNTING BRACKET NO.2 RH
3. INSTALL ENGINE MOVING CONTROL ROD W/BRACKET
4. INSTALL ENGINE MOUNTING STAY NO.2 RH
5. INSTALL FRONT FENDER APRON SEAL RH
6. INSTALL FRONT FENDER SPLASH SHIELD FRONT RH
7. INSTALL FRONT WHEEL RH
COMPONENTS (Part 1):
COMPONENTS (Part 1):
REMOVAL
1. REMOVE FRONT WHEEL RH
2. REMOVE FRONT FENDER SPLASH SHIELD FRONT RH
3. REMOVE FRONT FENDER APRON SEAL RH
4. REMOVE ENGINE MOUNTING STAY NO.2 RH
5. REMOVE ENGINE COVER SUB-ASSEMBLY NO.1
6. REMOVE ENGINE MOVING CONTROL ROD W/BRACKET
7. REMOVE ENGINE MOUNTING BRACKET NO.2 RH
8. REMOVE FAN AND GENERATOR V BELT
(a) Slowly turn the belt tensioner clockwise for more than 3 seconds, and remove the drive belt by using SST.
SST 09843-18030
INSTALLATION
1. INSTALL FAN AND GENERATOR V BELT
(a) Slowly turn the belt tensioner clockwise for more than 3 seconds, and install the drive belt by using SST.
SST 09249-63010
2. INSTALL ENGINE MOUNTING BRACKET NO.2 RH
3. INSTALL ENGINE MOVING CONTROL ROD W/BRACKET
4. INSTALL ENGINE MOUNTING STAY NO.2 RH
5. INSTALL FRONT FENDER APRON SEAL RH
6. INSTALL FRONT FENDER SPLASH SHIELD FRONT RH
7. INSTALL FRONT WHEEL RH
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.