Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2006SEQUOIA 4WD V8-4.7L (2UZ-FE)REPAIR AND DIAGNOSISTRANSMISSION AND DRIVETRAINAUTOMATIC TRANSMISSION/TRANSAXLETRANSMISSION POSITION SENSOR/SWITCHSERVICE AND REPAIR
2006 Toyota Sequoia 4WD V8-4.7L (2UZ-FE)
Transmission Position Sensor/Switch: Service and Repair
2006 Toyota Sequoia 4WD V8-4.7L (2UZ-FE)SECTION Service and Repair
PARK/ NEUTRAL POSITION SWITCH
REMOVAL
1. DISCONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a. Pry off the lock washer and remove the nut.
b. Remove the bolt and park/neutral position switch.
ADJUSTMENT
1. ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a. Loosen the park/neutral position switch bolt and move the shift lever to N.
b. Align the switch groove with the neutral basic line.
c. Hold the switch in position and tighten the bolt.
Torque: 13 Nm (1,130 kgf-cm, 10 ft. lbs.)
INSTALLATION
1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a. Install the park/neutral position switch with the bolt.
Torque: 13 Nm (1,130 kgf-cm, 10 ft. lbs.)
b. Install a new lock washer and the nut.
Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.)
c. Bend the claws on the lock washer to stake the nut.
d. Adjust the park/neutral position switch.
2. CONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
REMOVAL
1. DISCONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a. Pry off the lock washer and remove the nut.
b. Remove the bolt and park/neutral position switch.
ADJUSTMENT
1. ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a. Loosen the park/neutral position switch bolt and move the shift lever to N.
b. Align the switch groove with the neutral basic line.
c. Hold the switch in position and tighten the bolt.
Torque: 13 Nm (1,130 kgf-cm, 10 ft. lbs.)
INSTALLATION
1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a. Install the park/neutral position switch with the bolt.
Torque: 13 Nm (1,130 kgf-cm, 10 ft. lbs.)
b. Install a new lock washer and the nut.
Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.)
c. Bend the claws on the lock washer to stake the nut.
d. Adjust the park/neutral position switch.
2. CONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.