SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2005MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSISGENERAL INFORMATIONOBD-II DRIVE CYCLESDRIVE CYCLESVVTVVT DRIVE CYCLE 2
2005 Toyota Matrix XR, FWD, Standard

VVT Drive Cycle 2

2005 Toyota Matrix XR, FWD, StandardSECTION VVT Drive Cycle 2
Fig 1: Drive Cycle Pattern 2
G00526363Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
  7. Drive the vehicle for 5 minutes or more [C].
    CAUTION: When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  8. Idle the engine for 30 seconds or more [D].
  9. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  10. Read the pending DTCs.
    NOTE:
    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P0011, P0012, P0021 or P0022.
  13. Check the DTC judgment result.
    JUDGMENT RESULT

    TECHSTREAM DISPLY DESCRIPTION
    NORMAL
    • DTC judgment completed
    • System normal
    ABNORMAL
    • DTC judgment completed
    • System abnormal
    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit
    NOTE:
    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [F] through [H].
  14. Drive the vehicle for 5 minutes or more [F].
    CAUTION: When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  15. Idle the engine for 30 seconds or more [G].
  16. Enter the following menus: Powertrain / Engine / Trouble Codes [H].
  17. Read the pending DTCs.
    NOTE:
    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  18. Check the DTC judgment result again.
    NOTE:
    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or UNKNOWN, perform the following procedure.
  19. Perform a universal trip and check for permanent DTCs.
    NOTE:
    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTC is output, the system is normal.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.