Rear Axle LH Hub Bolt: Replacement

HINT:

COMPONENTS:

FF: SEE REAR AXLE HUB & BEARING ASSY LH (FF) 

4WD: SEE REAR AXLE CARRIER SUB-ASSY LH (4WD) 

1. REMOVE REAR WHEEL 
2. SEPARATE REAR DISC BRAKE CALIPER ASSY LH (DISC REAR BRAKE TYPE) (SEE  REPLACEMENT  ) 
3. REMOVE REAR DISC (DISC REAR BRAKE TYPE) 
4. SEPARATE REAR STABILIZER LINK ASSY LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
5. REMOVE REAR AXLE SHAFT LH NUT (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 

   SST 09930-00010

6. REMOVE REAR BRAKE DRUM SUB-ASSY (DRUM REAR BRAKE TYPE) 
7. SEPARATE SPEED SENSOR REAR LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
8. REMOVE PARKING BRAKE SHOE STRUT SET LH (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 

   SST 09703-30010

9. REMOVE FRONT BRAKE SHOE (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 

   SST 09718-00010

10. REMOVE REAR BRAKE AUTOMATIC ADJUST LEVER LH (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
11. REMOVE REAR BRAKE SHOE (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 

    SST 09718-00010

12. SEPARATE PARKING BRAKE CABLE ASSY NO.3 (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
13. SEPARATE REAR BRAKE TUBE NO.4 (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 

    SST 09023-00100

14. SEPARATE REAR SUSPENSION ARM ASSY NO.1 LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
15. SEPARATE UPPER CONTROL ARM ASSY (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
16. REMOVE REAR AXLE ASSY LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
17. REMOVE REAR WHEEL BEARING DUST DEFLECTOR NO.1 LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
18. REMOVE REAR AXLE HUB & BEARING ASSY LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
19. REMOVE REAR AXLE LH HUB BOLT (2WD DRIVE TYPE) 
    1. Using SST and a hammer handle or an equivalent, remove the LH hub bolt.

       SST 09628-10011

       Fig 1: Removing LH Hub Bolt

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
20. REMOVE REAR AXLE LH HUB BOLT (4WD DRIVE TYPE) 
    1. Using a press, remove the LH hub bolt.
       Fig 2: Removing LH Hub Bolt

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
21. INSTALL REAR AXLE LH HUB BOLT (2WD DRIVE TYPE) 
    1. Install a washer and nut to a new LH hub bolt as shown in the illustration.
    2. Using a hammer handle or an equivalent to hold the hub & bearing assy, install the LH hub bolt by tightening the nut.
       Fig 3: Installing Rear Axle LH Hub Bolt

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
22. INSTALL REAR AXLE LH HUB BOLT (4WD DRIVE TYPE) 
    1. Using a press and a extension bar, install a new LH hub bolt.
       Fig 4: Installing New LH Hub Bolt

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
23. INSTALL REAR AXLE HUB & BEARING ASSY LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
24. INSTALL REAR WHEEL BEARING DUST DEFLECTOR NO.1 LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 

    SST 09608-10010, 09950-60020 (09951-00680), 09950-70010 (09951-07100)

25. TEMPORARILY TIGHTEN UPPER CONTROL ARM ASSY (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
26. INSTALL REAR AXLE ASSY LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
27. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSY NO.1 LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
28. INSTALL REAR BRAKE TUBE NO.4 (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 

    SST 09023-00100

29. CONNECT PARKING BRAKE CABLE ASSY NO.3 (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
30. APPLICATION HIGH TEMPERATURE GREASE (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
31. INSTALL REAR BRAKE SHOE (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 

    SST 09718-00010

32. INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
33. INSTALL FRONT BRAKE SHOE (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 

    SST 09718-00010

34. INSTALL PARKING BRAKE SHOE STRUT SET LH (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
35. SPEED SENSOR REAR LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
36. CHECK REAR DRUM BRAKE INSTALLATION (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
37. INSTALL REAR BRAKE DRUM SUB-ASSY (DRUM REAR BRAKE TYPE) 
38. INSTALL REAR AXLE SHAFT LH NUT (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
39. REMOVE REAR BRAKE DRUM SUB-ASSY (4WD DRIVE TYPE) 
40. INSPECT BEARING BACKLASH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
41. INSPECT AXLE HUB DEVIATION (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
42. INSTALL REAR BRAKE DRUM SUB-ASSY (4WD DRIVE TYPE) 
43. ADJUST REAR DRUM BRAKE SHOE CLEARANCE (4WD DRIVE TYPE) (SEE  OVERHAUL  ) 
44. INSTALL REAR AXLE SHAFT LH NUT (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
45. INSTALL REAR STABILIZER LINK ASSY LH (4WD DRIVE TYPE) (SEE  REPLACEMENT  ) 
46. BLEED BRAKE LINE (4WD DRIVE TYPE) (SEE  BRAKE FLUID  ) 
47. INSTALL REAR DISC (DISC REAR BRAKE TYPE) 
48. INSTALL REAR DISC BRAKE CALIPER ASSY LH (DISC REAR BRAKE TYPE) (SEE  REPLACEMENT  ) 
49. INSTALL REAR WHEEL 

    Torque: 103 N.m (1,050 kgf.cm, 76 ft.lbf) 

50. STABILIZE SUSPENSION (4WD DRIVE TYPE) 
51. FULLY TIGHTEN UPPER CONTROL ARM ASSY (4WD DRIVE TYPE) (SEE  UPPER CONTROL ARM ASSY (4WD)  ) 
52. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.1 LH (4WD DRIVE TYPE) (SEE  REAR SUSPENSION ARM ASSY NO.1 LH (4WD)  ) 
53. CHECK FLUID LEVEL IN RESERVOIR (4WD DRIVE TYPE) 
54. INSPECT AND ADJUST REAR WHEEL ALIGNMENT (4WD DRIVE TYPE) (SEE  REAR WHEEL ALIGNMENT (4WD)  ) 
55. CHECK ABS SPEED SENSOR SIGNAL (4WD DRIVE TYPE) 
    1. ABS WITH EBD & BA & TRAC & VSC SYSTEM (SEE  DTC CHECK/CLEAR  ) 
    2. ABS WITH EBD SYSTEM (SEE  DTC CHECK/CLEAR  )