Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2005ECHO L4-1.5L (1NZ-FE)REPAIR AND DIAGNOSISWIPER AND WASHER SYSTEMSSERVICE AND REPAIRREAR WIPER AND WASHER (HATCHBACK)
2005 Toyota Echo L4-1.5L (1NZ-FE)
Rear Wiper and Washer (Hatchback)
2005 Toyota Echo L4-1.5L (1NZ-FE)SECTION Rear Wiper and Washer (Hatchback)
REMOVAL
1. REMOVE REAR WIPER ARM
a. Remove the rear wiper head cap.
b. Remove the nut and rear wiper arm.
c. Remove the grommet.
2. REMOVE BACK DOOR TRIM BOARD
a. Using a clip remover, pull out the 8 clips.
b. Remove the back door trim board.
3. REMOVE REAR WIPER MOTOR
a. Remove the 2 bolts and loosen the bolt indicated by the arrow in the illustration.
b. Disconnect the connector, then remove the rear wiper motor.
4. REMOVE WASHER NOZZLE
a. Remove the nozzle.
b. Disconnect the washer hose.
INSTALLATION
1. INSTALL WASHER NOZZLE
2. INSTALL REAR WIPER MOTOR
a. Install the rear wiper motor to the door panel with the 3 bolts.
Torque: 5.5 N.m (55 kgf.cm, 48 in.lbf)
b. Connect the connector.
3. INSTALL BACK DOOR TRIM BOARD
Install the back door trim board with the 8 clips.
4. INSTALL REAR WIPER ARM
a. Install the grommet.
b. Operate the wiper motor once and turn off the wiper switch.
c. Install the rear wiper arm and tighten the nut by hand.
d. Adjust the wiper arm to the position shown in the illustration.
A: Approx. 53.8 mm (2.118 in.)
e. Tighten the nut.
Torque: 5.5 N.m (55 kgf.cm, 48 in.lbf)
1. REMOVE REAR WIPER ARM
a. Remove the rear wiper head cap.
b. Remove the nut and rear wiper arm.
c. Remove the grommet.
2. REMOVE BACK DOOR TRIM BOARD
a. Using a clip remover, pull out the 8 clips.
b. Remove the back door trim board.
3. REMOVE REAR WIPER MOTOR
a. Remove the 2 bolts and loosen the bolt indicated by the arrow in the illustration.
b. Disconnect the connector, then remove the rear wiper motor.
4. REMOVE WASHER NOZZLE
a. Remove the nozzle.
b. Disconnect the washer hose.
INSTALLATION
1. INSTALL WASHER NOZZLE
2. INSTALL REAR WIPER MOTOR
a. Install the rear wiper motor to the door panel with the 3 bolts.
Torque: 5.5 N.m (55 kgf.cm, 48 in.lbf)
b. Connect the connector.
3. INSTALL BACK DOOR TRIM BOARD
Install the back door trim board with the 8 clips.
4. INSTALL REAR WIPER ARM
a. Install the grommet.
b. Operate the wiper motor once and turn off the wiper switch.
c. Install the rear wiper arm and tighten the nut by hand.
d. Adjust the wiper arm to the position shown in the illustration.
A: Approx. 53.8 mm (2.118 in.)
e. Tighten the nut.
Torque: 5.5 N.m (55 kgf.cm, 48 in.lbf)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.