Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2005CELICA GT-S, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTANTI-THEFT SYSTEMSVIP RS3200 PLUSINTRODUCTIONBRIEF DESCRIPTION - RS3200 PLUS FEATURES
2005 Toyota Celica GT-S, Standard
Brief Description - RS3200 Plus Features
2005 Toyota Celica GT-S, StandardSECTION Brief Description - RS3200 Plus Features
RS3200 PLUS FEATURES DESCRIPTION
| FEATURES | FUNCTIONS |
|---|---|
| REMOTE ARMING/DISARMING | The RS3200 PLUS will ARM 30 seconds after the lock button on the remote keyless entry system's remote control is pressed. If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. |
| AUTOMATIC REARMING | The RS3200 PLUS will automatically REARM at the same time the vehicle's remote keyless entry system re-locks the vehicle's doors, if no door is opened within 30 seconds after REMOTE DISARMING. |
| KEY ARMING/DISARMING | The RS3200 PLUS will ARM 30 seconds after you close the trunk (if open) and lock the vehicle's doors with the key, and will DISARM when you unlock a door with the key. |
| MANUAL ARMING | When you lock the vehicle with the central lock switch (while a door is open), the RS3200 PLUS will ARM 30 seconds after you close all the doors and the trunk (if open). |
| IGNITION KEY DISARMING | The RS3200 PLUS may be DISARMED by inserting the key into the ignition switch and turning it to "ON". |
| POINT-OF-ENTRY PROTECTION | Forcibly unlocking or opening a door or trunk while the RS3200 PLUS is ARMED will TRIGGER and ALARM immediately. |
| GLASS BREAKAGE SENSOR | The RS3200 PLUS utilizes a microphone (usually mounted in the STATUS MONITOR) to sense the noise from tapping on window glass, or glass breaking, and TRIGGER the system to sound an ALARM. It is fine tuned to "listen" for this type of noise, and ignore other sounds. |
| WARN AWAY ALARM | When the GLASS BREAKAGE SENSOR'S microphone picks up tapping or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and markers lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of glass tapping or breaking, or if a door is opened or unlocked without a key, the regular ALARM is TRIGGERED. |
| IGNITION SWITCH MONITORING | While ARMED, the RS3200 PLUS monitors the ignition switch. If an attempt is made to start the vehicle without a key, an ALARM is TRIGGERED. |
| STARTER DISABLE | When an ALARM is TRIGGERED, the system disables the vehicle's starter and prevents engine start until the system is reset (DISARMED). |
| TRIGGER MEMORY | The user is notified that an ALARM occurred. Upon DISARMING, the system after an ALARM was TRIGGERED, the vehicle's tail and marker lights will be turned on for 2 seconds. |
| EXTERIOR LIGHT ACTIVATION | The RS3200 PLUS flashes the vehicle's tail and marker lights or turn signal lights during REMOTE ARMING and REMOTE DISARMING, and during an ALARM. Also, during an ALARM, the headlights flash. |
| BUZZER ACTIVATION | If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote keyless entry system's remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. |
| HORN ACTIVATION | During an ALARM, the RS3200 PLUS activates the vehicle's horn. |
| POWER LOSS MEMORY | If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM is TRIGGERED once power is restored. |
| STATUS MONITOR | This panel houses the GLASS BREAKAGE SENSOR microphone and the flashing LED that indicates the operating status of the security system. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.