2005 Toyota Avalon XLSFACTORY OEM SERVICE PROCEDURE

Inspection Procedure

  1. READ VALUE OF HAND-HELD TESTER 
    1. Connect the hand-held tester to the DLC3.
    2. Turn the engine switch on (IG).
    3. Following the display on the tester, select "DATA LIST".

      SMART KEY (Certification ECU): 

      Fig 1: Smart Key (Certification ECU) Data List
      G02977167Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: 

      "ON" (lock switch is pressed) appears on the tester screen. 

    1. OK : PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN  PROBLEM SYMPTOMS TABLE  
    2. NG : Go to next step. 
  2. INSPECT LOCK SWITCH 
    1. Remove the outside handle.
    2. Disconnect the connectors.
    3. Measure the resistance according to the value (s) in the table below.

      Standard: 

      LOCK SWITCH RESISTANCE

      Tester Connection Condition Specified Condition
      V1-1 (TRG-) - V1-3 (TRG+) Lock switch not pushed --> Pushed 10 kΩ or higher --> Below 1 Ω
      V2-1 (TRG-) - V2-3 (TRG+) Lock switch not pushed --> Pushed 10 kΩ or higher --> Below 1 Ω
      V3-1 (TRG-) - V3-3 (TRG+) Lock switch not pushed --> Pushed 10 kΩ or higher --> Below 1 Ω
      V4-1 (TRG-) - V4-3 (TRG+) Lock switch not pushed --> Pushed 10 kΩ or higher --> Below 1 Ω
      Fig 2: Inspecting Lock Switch
      G02977168Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG : REPLACE OUTSIDE HANDLE (SEE  REPLACEMENT  ) 
    2. OK : Go to next step. 
  3. CHECK WIRE HARNESS (CERTIFICATION ECU - LOCK SWITCH) 
    1. Disconnect the D39 and D40 ECU connectors.
    2. Measure the resistance according to the value (s) in the table below.

      Standard: 

      CERTIFICATION ECU - LOCK SWITCH RESISTANCE

      Tester Connection Condition Specified Condition
      D39-3 (TSW1) - V1-3 (TRG+) Always Below 1 Ω
      D39-4 (TSW2) - V2-3 (TRG+) Always Below 1 Ω
      D40-25 (TSW3) - V3-3 (TRG+) Always Below 1 Ω
      D40-26 (TSW4) - V4-3 (TRG+) Always Below 1 Ω
      D39-3 (TSW1) - Body ground Always 10 kΩ or higher
      D39-4 (TSW2) - Body ground Always 10 kΩ or higher
      D40-25 (TSW3) - Body ground Always 10 kΩ or higher
      D40-26 (TSW4) - Body ground Always 10 kΩ or higher
      Fig 3: Identifying Certification ECU Connector D39, D40 Terminals
      G02977169Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.