SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2004MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 764 (THEFT DETERRENT SYSTEMS)POWER DOOR LOCK CONTROL SYSTEMON-VEHICLE INSPECTION
2004 Toyota Matrix XR, FWD, Standard

On-Vehicle Inspection

2004 Toyota Matrix XR, FWD, StandardSECTION On-Vehicle Inspection
WARNING: This page is about a different car, the 2004 Lexus ES 330. However, it is still accessible from the selected car via links, so may be relevant.
  1. DOOR LOCK FAIL-SAFE 
    1. When a malfunction in the door control switch (manual switch, interlocked with key operation) has been detected door LOCK/UNLOCK operations become unable.
  2. CHECK FOR ELECTRICAL DOOR LOCK OPERATION 
    1. Check the basic function.
      1. Check that all doors will lock when the door control switch (for manual operation) is turned to the lock side and all doors will unlock when turned to the unlock side.
      2. Check all doors will lock when the driver's door is operated to be lock and all doors will unlock when operated to be unlock, by the key operation outside the vehicle.
    2. Check the key confinement prevention function.
      NOTE: In order to prevent the key from being confined, the inspection should be made with the driver's door glass open.
      1. Have the ignition key inserted into the ignition key cylinder.
      2. With the driver's door open, check all doors will immediately unlock when the door lock knob for the driver's door is turned to the lock side.
      3. With the driver's door open, check all doors will immediately unlock when the door control switch (for manual operation) is turned to the lock side.
      4. With the driver's door open, make the driver's door lock by holding the driver's door lock knob in the lock side for 2 seconds or more and then close the driver's door, then check that all doors will unlock.
    3. Check the security function.
      1. Close all doors with the driver's door glass open so that the door control switch can be operated outside the vehicle.
      2. Pull out the ignition key, open the driver's door and close and lock the door without a key operation. Under this condition, check that all doors will not unlock when the door control switch (for manual operation) is turned to the unlock outside the vehicle.
      3. Pull out the ignition key, close and lock the driver's door by a key operation. Under this condition, check that all doors will not unlock when the door control switch (for manual operation) is turned to the unlock outside the vehicle.
      4. Pull out the ignition key, close the driver's door and lock the door by a wireless door lock operation. Under this condition, check that all doors will not unlock when the door control switch (for manual operation) is turned to the unlock outside the vehicle.

      HINT:

      Under the conditions below, check that the security function will cancel.

      • Ignition switch turned ON.
      • Driver's door is unlocked by a key operation.
      • Door control switch (for manual operation) turned to the unlock side after the door control knob has been unlocked manually.
      • Doors are unlocked by a wireless operation.
    4. Check the illumination function.
      1. Set the map light switch in the DOOR position.
      2. Check that the map light will be on simultaneously with all doors' unlocking operation when only the driver's door out of all the locking doors is turned to the unlock side by a key operation.
      3. Map light will be off in approximately 15 seconds if a door has not been opened for a while.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.