SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2004MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 759 (AUTOMATIC TRANSAXLE (ON-VEHICLE SERVICE))FLOOR SHIFT ASSYOVERHAUL
2004 Toyota Matrix XR, FWD, Standard

Floor Shift ASSY: Overhaul

2004 Toyota Matrix XR, FWD, StandardSECTION Overhaul
WARNING: This page is about a different car, the 2004 Lexus ES 330. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE FRONT DOOR SCUFF PLATE LH (SEE  REPLACEMENT  ) 
  2. REMOVE FRONT DOOR SCUFF PLATE RH (SEE  REPLACEMENT  ) 
  3. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO. 1 (SEE  REPLACEMENT  ) 
  4. REMOVE INSTRUMENT PANEL SUB-ASSY LOWER (SEE  REPLACEMENT  ) 
  5. REMOVE INSTRUMENT PANEL SUB-ASSY UPPER (SEE  REPLACEMENT  ) 
  6. REMOVE INSTRUMENT PANEL INSERT SUB-ASSY LOWER LH (SEE  REPLACEMENT  ) 
  7. REMOVE CONSOLE BOX ASSY (SEE  REPLACEMENT  ) 
  8. REMOVE CONSOLE BOX CARPET 
  9. REMOVE CONSOLE BOX ASSY (SEE  REPLACEMENT  ) 
  10. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (SEE  REPLACEMENT  ) 
  11. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (SEE  REPLACEMENT  ) 
  12. REMOVE AIR DUCT REAR NO. 1 (SEE  OVERHAUL  ) 
  13. REMOVE AIR DUCT REAR NO. 2 (SEE  OVERHAUL  ) 
  14. REMOVE CONSOLE BOX DUCT NO. 1 (SEE  OVERHAUL  ) 
  15. DISCONNECT FLOOR SHIFT PARKING LOCK CABLE ASSY 
    1. Disconnect the parking lock cable end from the lever pin of the floor shift assembly.
      Fig 1: Disconnecting Parking Lock Cable End From Lever Pin Of Floor Shift Assembly
      G00900033Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver, disconnect the parking lock cable from the floor shift assembly and clamp.
    3. Disconnect the cable clamp.
      Fig 2: Disconnecting Parking Lock Cable From Floor Shift Assembly And Clamp
      G00900034Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. DISCONNECT TRANSMISSION CONTROL CABLE ASSY 
    1. Disconnect the floor shift transmission control cable from the rod of the floor shift assy.
      Fig 3: Disconnecting Transmission Control Cable Assy
      G00900035Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE FLOOR SHIFT ASSY 
    1. Disconnect the shift lock control computer connector.
    2. Disconnect the indicator lamp wire connector.
    3. Remove the 4 bolts and transmission floor shift assy.
      Fig 4: Removing Floor Shift Assy With Bolts
      G00900036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE SHIFT LEVER KNOB SUB-ASSY 
    1. Remove the floor shift lever knob from the shift lever.
      Fig 5: Removing Floor Shift Lever Knob From Shift Lever
      G00900037Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSY 
    1. Disconnect the wire harness from the clamp.
      Fig 6: Disconnecting Wire Harness From Clamp
      G00900038Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver, release the 4 claws and remove the position indicator housing.
      Fig 7: Releasing Claws And Removing Position Indicator Housing
      G00900039Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE POSITION INDICATOR LIGHT GUIDE 
    1. Using screwdriver, release the 4 claws and remove the position indicator light guide.
      Fig 8: Removing Position Indicator Light Guide
      G00900040Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE INDICATOR LAMP WIRE SUB-ASSY 
    1. Remove the indicator lamp wire from the position indicator light guide.
      Fig 9: Removing Indicator Lamp Wire From Position Indicator Light Guide
      G00900041Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE POSITION INDICATOR LAMP CAP 
    1. Remove the floor shift position indicator lamp cap from the floor shift position indicator lamp bulb.
  23. REMOVE POSITION INDICATOR LAMP BULB 
    1. Remove the floor shift position indicator lamp bulb from the indicator lamp wire.
  24. REMOVE SHIFT LOCK RELEASE BUTTON COVER 
    1. Using a screwdriver, remove the shift lock release button cover.
      Fig 10: Removing Shift Lock Release Button Cover
      G00900042Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. REMOVE POSITION INDICATOR SLIDE COVER 
    1. Remove the position indicator slide cover from the shift lever.
      Fig 11: Removing Position Indicator Slide Cover From Shift Lever
      G00900043Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. REMOVE POSITION INDICATOR SLIDE COVER 
    1. Remove the position indicator slide cover from the position indicator slide cover.
      Fig 12: Removing Position Indicator Slide Cover
      G00900044Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. REMOVE SHIFT LOCK RELEASE BUTTON 
    1. While pressing the 2 claws, remove the shift lock release button and shift lock release spring.
      Fig 13: Removing Shift Lock Release Button
      G00900045Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. INSTALL SHIFT LOCK RELEASE BUTTON 
    1. Apply MP grease to the shift lock release spring and shift lock release button.
    2. Install the shift lock release button and shift lock release spring to the shift lever.
      Fig 14: Installing Shift Lock Release Button
      G00900046Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. INSTALL POSITION INDICATOR SLIDE COVER 
    1. Install the position indicator slide cover the position indicator slide cover.
      Fig 15: Installing Position Indicator Slide Cover
      G00900047Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. INSTALL POSITION INDICATOR SLIDE COVER 
    1. Install the position indicator slide cover to the shift lever.
      Fig 16: Installing Position Indicator Slide Cover To Shift Lever
      G00900048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. INSTALL POSITION INDICATOR LAMP BULB 
    1. Install the floor shift position lamp bulb to the indicator wire.
  32. INSTALL POSITION INDICATOR LAMP CAP 
    1. Install the floor shift position indicator lamp cap to the floor shift position indicator lamp bulb.
  33. INSTALL INDICATOR LAMP WIRE SUB-ASSY 
    1. Install the indicator lamp wire to the position indicator light guide.
      Fig 17: Installing Indicator Lamp Wire To Position Indicator Light Guide
      G00900049Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. INSTALL POSITION INDICATOR LIGHT GUIDE 
    1. Install the position indicator light guide to the floor shift position indicator housing.

      HINT:

      Fit the claws securely.

      Fig 18: Installing Position Indicator Light Guide
      G00900050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSY 
    1. Install the floor shift position indicator housing to the shift lever.

      HINT:

      Fit the Claws securely.

      Fig 19: Installing Floor Shift Position Indicator Housing To Shift Lever
      G00900051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. INSTALL SHIFT LOCK RELEASE BUTTON COVER 
    1. Install the shift lock release button cover to the position indicator housing.
      Fig 20: Installing Shift Lock Release Button Cover To Position Indicator Housing
      G00900052Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  37. INSTALL SHIFT LEVER KNOB SUB-ASSY 
    1. Install the floor shift lever knob to the shift lever.
      Fig 21: Installing Floor Shift Lever Knob To Shift Lever
      G00900053Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. INSTALL FLOOR SHIFT ASSY 
    1. Install the floor shift assy to the vehicle with the 4 bolts.

      Torque: 11.8 N.m (122 kgf.cm, 9ft.lbf) 

    2. Connect the shift lock control computer.
    3. Connect the indicator lamp wire connector.
      Fig 22: Installing Floor Shift Assy To Vehicle With Bolts
      G00900054Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  39. INSTALL TRANSMISSION CONTROL CABLE ASSY 
    1. Install the floor shift transmission control cable to the shift lever.

      HINT:

      Install it with the uneven surface facing up.

      Fig 23: Installing Floor Shift Transmission Control Cable To Shift Lever
      G00900055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  40. INSTALL FLOOR SHIFT PARKING LOCK CABLE ASSY 
    1. Using a screwdriver, unlock the claw of the lock key of automatic adjustment part.
      Fig 24: Installing Floor Shift Parking Lock Cable Assy (1 Of 4)
      G00900056Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Insert the slide cap into the through hole and install.
    3. Shift the shift lever to P position and turn the ignition switch to Lock.
      Fig 25: Installing Floor Shift Parking Lock Cable Assy (2 Of 4)
      G00900057Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Insert the lever pin into the hole of the parking lock cable.
      Fig 26: Installing Floor Shift Parking Lock Cable Assy (3 Of 4)
      G00900058Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Lock the lock key.
      Fig 27: Installing Floor Shift Parking Lock Cable Assy (4 Of 4)
      G00900059Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  41. INSTALL BATTERY 
  42. ADJUST SHIFT LEVER POSITION (SEE  ADJUSTMENT  ) 
  43. INSPECT SHIFT LEVER POSITION (SEE  ADJUSTMENT  ) 
  44. INSPECT CHECK KEY INTERLOCK OPERATION (SEE  ON-VEHICLE INSPECTION  ) 
  45. INSPECT CHECK SHIFT LOCK OPERATION (SEE  ON-VEHICLE INSPECTION  ) 
  46. INSPECT CHECK SHIFT LOCK RELEASE BUTTON OPERATION (SEE  ON-VEHICLE INSPECTION  ) 
  47. INSTALL CONSOLE BOX DUCT NO. 1 (SEE  OVERHAUL  ) 
  48. INSTALL AIR DUCT REAR NO. 2 (SEE  OVERHAUL  ) 
  49. INSTALL AIR DUCT REAR NO. 1 (SEE  OVERHAUL  ) 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.