Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2004MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 236 (WHEEL ALIGNMENT SPECIFICATIONS & ADJUSTMENT PROCEDURES)SIENNASPECIFICATIONS
2004 Toyota Matrix XR, FWD, Standard
Section 236 (Wheel Alignment Specifications & Adjustment Procedures): Sienna: Specifications
2004 Toyota Matrix XR, FWD, StandardSECTION Specifications
WARNING: This page does not describe the selected car, but rather 16 other vehicles, including the 2002 Toyota Tundra, 2002 Toyota Tacoma, 2002 Toyota Sienna, 2002 Toyota Sequoia, and 2002 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
Wheel Alignment Specifications (Sienna)
| Cold tire inflation pressure (Normal driving) | P205/70R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 , 35 bar or psi) | |||||||||
| P215/65R1595S | Front, Rear | 220 kPa (2.2 kgf/cm2
, 32 bar or psi)(1) 240 kPa (2.4 kgf/cm2 ,35 bar or psi)(2) |
||||||||||
| Cold tire inflation pressure (Trailer towing) | P205/70R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 ,35 bar or psi) | |||||||||
| P215/65R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 ,35 bar or psi) | ||||||||||
| Front wheel alignment | Vehicle height | 205/70R15 | Front(3) | 230 mm (9.06 in.) | ||||||||
| Rear(4) | 324 mm (12.76 in.) | |||||||||||
| 215/65R15 | Front(3) | 226 mm (8.90 in.) | ||||||||||
| Rear(4) | 320 mm (12.60 in.) | |||||||||||
| Camber | -0°32' ± 45' (-0.5° ± 0.75°) | |||||||||||
| Left - right error | 45' (0.75°) or less | |||||||||||
| Caster | 1°32' ± 45' (1.53° ± 0.75°) | |||||||||||
| Left-right error | 45' (0.75°) or less | |||||||||||
| Steering axis inclination | 12°35' ± 45' (12.58° ± 0.75°) | |||||||||||
| Toe-in (Total) | 0°16' ± 12' (0.27° ± 0.2°) 2.6 ± 2 mm (0.10 ± 0.08 in.) |
|||||||||||
| Rack end length difference | 1.5 mm (0.059 in.) or less | |||||||||||
| Wheel angle | Inside wheel | 34°19' ± 1° (34.32° ± 1°) | ||||||||||
| Outside wheel < Reference > | 30° 19' (30.32°) | |||||||||||
| Rear wheel alignment | Camber | -0°55' + 45' (-0.92° ± 0.75°) | ||||||||||
| Left-right error | 45' (0.75°) or less | |||||||||||
| Toe-in (Total) | 0°13' ± 18' (0.22° ± 0.30°) | |||||||||||
| 2.2 ± 3 mm (0.09 ± 0.12 in.) | ||||||||||||
| Front axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | |||||||||
| Axle hub deviation | Maximum | 0.05 mm (0.0020 in.) | ||||||||||
| Front drive shaft | Drive shaft standard length | LH | 586.0 ± 2.0 mm (23.071 ± 0.079 in.) | |||||||||
| RH | 881.6 ± 2.0 mm (34.709 ± 0.079 in.) | |||||||||||
| Front suspension | Lower ball joint turning torque | 1.0 - 3.4 N.m (10 - 35 kgf.cm, 8.7 - 30 in..lbf) | ||||||||||
| Stabilizer bar link turning torque | 0.05 -1.0 N.m (0.5-10 kgf.cm, 0.4 - 8.7 in..lbf) | |||||||||||
| Rear axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | |||||||||
| Axle hub deviation | Maximum | 0.07 mm (0.0028 in.) | ||||||||||
Measure from the ground to the center of the front side lower suspension arm mounting bolt.
Measure from the ground to the center of the axle beam bushing. |
||||||||||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.