Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSTOYOTA2002HIGHLANDER 4WD L4-2.4L (2AZ-FE)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTECHNICAL SERVICE BULLETINSALL TECHNICAL SERVICE BULLETINSCANADA - ENGINE CONTROLS - AF SENSOR IDENTIFICATION
2002 Toyota Highlander 4WD L4-2.4L (2AZ-FE)
Canada - Engine Controls - AF Sensor Identification
2002 Toyota Highlander 4WD L4-2.4L (2AZ-FE)SECTION Canada - Engine Controls - AF Sensor Identification
Bulletin
TSB2088R
Issue Date
August 27, 2004
Market
Canada
Title
ENGINE BANK 1 AND BANK 2 A/F AND O2 IDENTIFICATION
Component
ENGINE ELECTRICAL
Models
'93 - '10 Applicable Toyota Models
TSB REVISION NOTICE
- March 4, 2010: Applicability has been updated to include 2009 - 2010 model year vehicles and 2006 - 2010 model year Highlander HV.
Any previous printed versions of this TSB should be discarded. Be sure to review the entire content of this service bulletin before proceeding.
INTRODUCTION:
This service bulletin provides information on the proper identification of engine bank 1 and engine bank 2 for correct A/F sensor and oxygen sensor replacement.
This bulletin contains information that identifies engine bank 1 and engine bank 2 on the following engines:
1AZ-FE, 2AZ-FE, 2AZ-FE (PZEV), 1GR-FE, 2GR-FE, 2JZ-GE, 1MZ-FE, 3MZ-FE, 1UR-FE, 3UR-FE, 2UZ-FE, 5VZ-FE, and 1ZZ-FE.
- Bank 1 [B1] refers to the bank that includes cylinder No. 1.
- Bank 2 [B2] refers to the bank opposite bank 1.
- Sensor 1 [S1] refers to the sensor that is located before the catalytic converters.
- Sensor 2 [S2] refers to the sensor that is located after the catalytic converters.
APPLICABILITY:
WARRANTY INFORMATION:
APPLICABLE VEHICLES:
ENGINE BANK IDENTIFICATION:
Figure 1. Engine Bank Identification: 1UR-FE, 3UR-FE, 2UZ-FE
Figure 2. Engine Bank Identification: 2GR-FE, 1MZ-FE, 3MZ-FE
Figure 3. Engine Bank Identification: 1GR-FE, 5VZ-FE
Figure 4. Engine Bank Identification: 2JZ-GE
Figure 5. Engine Bank Identification: 1ZZ-FE
Figure 6. Engine Bank Identification: 1AZ-FE
Figure 7. Engine Bank Identification: 2AZ-FE
Figure 8. Sensor Identification: FWD V6
Figure 9. Sensor Identification: 2AZ-FE PZEV
NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available. IT DOES NOT CONSTITUTE AN AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable, will apply.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.