Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2001LANDCRUISER V8-4.7L (2UZ-FE)REPAIR AND DIAGNOSISTRANSMISSION AND DRIVETRAINTRANSFER CASESERVICE AND REPAIRUNIT OVERHAULFRONT EXTENSION HOUSING
2001 Toyota Landcruiser V8-4.7L (2UZ-FE)
Front Extension Housing
2001 Toyota Landcruiser V8-4.7L (2UZ-FE)SECTION Front Extension Housing
DISASSEMBLY
1. REMOVE DRIVE CLUTCH HUB
a. Using a snap ring expander, remove the snap ring.
b. Using SST, remove the drive clutch hub.
SST 09950-40011 (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04021, 09957-04010, 09958-04011)
2. REMOVE FRONT OUTPUT SHAFT
Using a plastic hammer, drive out the front output shaft.
3. REMOVE DUST DEFLECTOR
a. Using SST, remove the dust deflector.
SST 09950-40011 (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)
b. Using a screwdriver and hammer, tap the dust deflector and remove it from the extension housing.
4. REMOVE OIL SEAL
Using a screwdriver, pry out the oil seal from the front extension housing.
5. REMOVE BALL BEARING
a. Using a screwdriver, remove the snap ring.
b. Using SST and a press, remove the ball bearing.
SST 09316-60011 (09316-00011, 09316-00071)
REASSEMBLY
HINT: Coat all of the sliding and rotating surfaces with gear oil before reassembly.
1. INSTALL DUST DEFLECTOR
a. Using a plastic hammer, install a new dust deflector to the front extension housing.
b. Using SST and a press, install a new dust deflector to the front output shaft.
SST 09316-20011, 09316-60011 (09316-00011)
2. INSTALL BALL BEARING
a. Using SST and a press, install the ball bearing to the front extension housing.
SST 09316-60011 (09316-00011, 09316-00031)
b. Select a snap ring that will allow the minimum axial play.
c. Using a screwdriver, install a new snap ring.
3. INSTALL OIL SEAL
a. Apply MP grease to the lip of a new oil seal.
b. Using SST and a hammer, drive in a new oil seal to the front extension housing.
SST 09316-60011 (09316-00011, 09316-00061)
4. INSTALL FRONT OUTPUT SHAFT AND DRIVE CLUTCH HUB
a. Using SST and a press, install the front output shaft and drive clutch hub.
SST 09316-20011, 09316-60011 (09316-00011, 09316-00041, 09316-00071)
b. Select a snap ring that will allow the minimum axial play.
c. Using a snap ring expander, install a new snap ring.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.