Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2001LANDCRUISER V8-4.7L (2UZ-FE)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTTRANSMISSION CONTROL SYSTEMSTESTING AND INSPECTIONINITIAL INSPECTION AND DIAGNOSTIC OVERVIEWDIAGNOSTIC STRATEGIESSERVICE HINTS
2001 Toyota Landcruiser V8-4.7L (2UZ-FE)
Service Hints
2001 Toyota Landcruiser V8-4.7L (2UZ-FE)SECTION Service Hints
ELECTRONICALLY CONTROLLED TRANSMISSION AND A/T INDICATOR
E4 ELECTRONICALLY CONTROLLED TRANSMISSION PATTERN SELECT SW
5 - 3 : Closed with select SW at PWR position
2 - 3 : Closed with select SW at 2nd position
E6 (B), E8 (D), E9 (E) ENGINE CONTROL MODULE
BATT - E1 : Always 9.0 - 14.0 volts
+B - E1 : 9.0 - 14.0 volts with ignition SW at ON or ST position
+B1 - E1 : 9.0 - 14.0 volts with ignition SW at ON or ST position
NSW - E1 : 9.0 - 14.0 volts with ignition SW at ST position
: 0 - 3.0 volts with ignition SW on and shift lever in P or N position
STA - E1 : 6.0 volts or more with ignition SW at ST position and shift lever in P or N position
P1 A/T INDICATOR LIGHT SW [PARK/NEUTRAL POSITION SW]
3 - 1 : Closed with shift lever in P position
3 - 2 : Closed with shift lever in R position
3 - 5 : Closed with shift lever in N position
3 - 7 : Closed with shift lever in D position
3 - 4 : Closed with shift lever in 2 position
3 - 8 : Closed with shift lever in L position
E4 ELECTRONICALLY CONTROLLED TRANSMISSION PATTERN SELECT SW
5 - 3 : Closed with select SW at PWR position
2 - 3 : Closed with select SW at 2nd position
E6 (B), E8 (D), E9 (E) ENGINE CONTROL MODULE
BATT - E1 : Always 9.0 - 14.0 volts
+B - E1 : 9.0 - 14.0 volts with ignition SW at ON or ST position
+B1 - E1 : 9.0 - 14.0 volts with ignition SW at ON or ST position
NSW - E1 : 9.0 - 14.0 volts with ignition SW at ST position
: 0 - 3.0 volts with ignition SW on and shift lever in P or N position
STA - E1 : 6.0 volts or more with ignition SW at ST position and shift lever in P or N position
P1 A/T INDICATOR LIGHT SW [PARK/NEUTRAL POSITION SW]
3 - 1 : Closed with shift lever in P position
3 - 2 : Closed with shift lever in R position
3 - 5 : Closed with shift lever in N position
3 - 7 : Closed with shift lever in D position
3 - 4 : Closed with shift lever in 2 position
3 - 8 : Closed with shift lever in L position
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.