SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUZUKI2013SX4 CROSSOVER, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 14 (AUTOMATIC TRANSMISSION)SPECIFICATIONSSHIM SIZE SPECIFICATIONS
2013 Suzuki SX4 Crossover, Automatic CVT Trans

Shim Size Specifications

2013 Suzuki SX4 Crossover, Automatic CVT TransSECTION Shim Size Specifications
WARNING: This page is about a different car, the 2007 Suzuki XL7. However, it is still accessible from the selected car via links, so may be relevant.
FRONT DIFFERENTIAL SIDE GEAR SHIM SIZE SPECIFICATIONS

Identification Specifications
Metric English
70 1.00 mm 0.039 in
71 1.05 mm 0.041 in
72 1.10 mm 0.043 in
73 1.15 mm 0.045 in
74 1.20 mm 0.047 in
75 1.25 mm 0.049 in
76 1.30 mm 0.051 in
77 1.33 mm 0.052 in
78 1.36 mm 0.054 in
79 1.39 mm 0.055 in
80 1.42 mm 0.056 in
81 1.45 mm 0.057 in
82 1.48 mm 0.058 in
83 1.51 mm 0.059 in
84 1.54 mm 0.061 in
85 1.57 mm 0.062 in
86 1.60 mm 0.0629 in
87 1.65 mm 0.0649 in
88 1.70 mm 0.0669 in
89 1.75 mm 0.0688 in
90 1.80 mm 0.070 in
91 1.85 mm 0.0728 in
92 1.90 mm 0.0748 in
FRONT DIFFERENTIAL TRANSFER DRIVE GEAR THRUST BEARING WASHER SPECIFICATIONS

Identification Washer Thickness (mm) Washer Thickness (in)
None 0.81 0.032
A 0.90 0.035
B 1.00 0.039
C 1.10 0.043
D 1.20 0.047
E 1.30 0.051
F 1.40 0.055
G 1.50 0.059
1-2 REVERSE INTERNAL GEAR WASHER SPECIFICATIONS

Identification Washer Thickness (mm) Washer Thickness (in)
8 0.81 0.032
9 0.90 0.035
10 1.00 0.039
11 1.10 0.043
12 1.20 0.047
13 1.30 0.051
14 1.40 0.055
15 1.50 0.059
16 1.60 0.063
FORWARD/DIRECT CLUTCH HOUSING THRUST WASHER SPECIFICATIONS

Identification Washer Thickness (mm) Washer Thickness (in)
None 0.81 0.032
9 0.90 0.035
10 1.00 0.039
11 1.10 0.043
12 1.20 0.047
13 1.30 0.051
14 1.40 0.055
15 1.50 0.059
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.