Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSSUZUKI2013SX4 CROSSOVER, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 14 (AUTOMATIC TRANSMISSION)REPAIR INSTRUCTIONSCONTROL VALVE REAR BODY ASSEMBLE

2013 Suzuki SX4 Crossover, Automatic CVT Trans

Control Valve Rear Body Assemble

2013 Suzuki SX4 Crossover, Automatic CVT TransSECTION Control Valve Rear Body Assemble

WARNING: This page is about a different car, the 2007 Suzuki XL7. However, it is still accessible from the selected car via links, so may be relevant.

Reference: CONTROL VALVE REAR BODY DISASSEMBLE .

Fig 1: Identifying Rear Control Valve Body

Courtesy of SUZUKI OF AMERICA CORP.

Inspect the rear control valve body (410) casting for the following conditions:
- Porosity
- Cracks
- Damaged machine surface
- Chips or debris
- Damage to valve bores
Inspect all valves, springs, bushings, and clean all components in clean solvent.

Fig 2: Identifying 1-2 Reverse Clutch Control Valve
Courtesy of SUZUKI OF AMERICA CORP.
Install the 1-2 reverse clutch (B5) control valve (411).

Fig 3: Identifying Lock Up Relay Control Valve Plunger & Sleeve
Courtesy of SUZUKI OF AMERICA CORP.
Install the lock up relay valve (415).
Install the lock up relay valve spring (414).
Install the lock up relay control valve plunger (413).
Install the lock up relay control valve sleeve (412).

Fig 4: Identifying Rear Valve Body Cover Plate Gasket & Plate
Courtesy of SUZUKI OF AMERICA CORP.
Install the rear valve body cover plate gasket (418).
Install the rear valve body cover plate (417).
CAUTION: Refer to FASTENER NOTICE .
Install the 2 - M5 x 0.8 x 13 mm rear valve body cover plate bolts (416).
Tightening torque

Tighten the cover plate bolts to 7 N.m (62 lb in) .

Fig 5: Identifying Third Gear Band Control Valve Spring & Valve
Courtesy of SUZUKI OF AMERICA CORP.
Install the third gear band (B4) control valve spring (422).
Install the third gear band (B4) control valve (423).

Fig 6: Identifying Shift Pressure Relay Valve & Spring
Courtesy of SUZUKI OF AMERICA CORP.
Install the shift pressure relay valve (424).
Install the shift pressure relay valve spring (425).

Fig 7: Identifying M2 Shift Valve Spring & M2 Shift Valve
Courtesy of SUZUKI OF AMERICA CORP.
Install the M2 shift valve (426).
Install the M2 shift valve spring (427).

Fig 8: Identifying Shift Pressure Control Valve Sleeve & Valve
Courtesy of SUZUKI OF AMERICA CORP.
Install the shift pressure control valve sleeve (428).
Install the shift pressure control valve spring (429).
Install the shift pressure control valve (430).
Install the shift pressure control valve plunger (431).
Install the shift pressure control valve plunger sleeve (432).

Fig 9: Identifying Line Pressure Control Accumulator Piston & Springs
Courtesy of SUZUKI OF AMERICA CORP.
Install the line pressure control (SLT) accumulator piston (433).
Install the line pressure control (SLT) accumulator piston spring - outer (434).
Install the line pressure control (SLT) accumulator piston spring - inner (435).

Fig 10: Identifying Secondary Regulator Valve Spring & Valve
Courtesy of SUZUKI OF AMERICA CORP.
Install the secondary regulator valve (436).
Install the secondary regulator valve spring (437).

Fig 11: Identifying Rear Valve Body Cover Plate Gasket & Plate
Courtesy of SUZUKI OF AMERICA CORP.
Install the rear valve body cover plate gasket (419).
Install the rear valve body cover plate (420).
Install the 7 - M5 x 0.8 x 13 mm rear valve body cover plate bolts (421).
Tightening torque

Tighten the cover plate bolts to 7 N.m (62 lb in) .

Reference: CONTROL VALVE BODY ASSEMBLY ASSEMBLE .