SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUZUKI2013SX4 CROSSOVER, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 14 (AUTOMATIC TRANSMISSION)REPAIR INSTRUCTIONSCONTROL VALVE FRONT BODY ASSEMBLE
2013 Suzuki SX4 Crossover, Automatic CVT Trans

Control Valve Front Body Assemble

2013 Suzuki SX4 Crossover, Automatic CVT TransSECTION Control Valve Front Body Assemble
WARNING: This page is about a different car, the 2007 Suzuki XL7. However, it is still accessible from the selected car via links, so may be relevant.

Reference: CONTROL VALVE FRONT BODY DISASSEMBLE .

Fig 1: Identifying Front Control Valve Body
G04846352Courtesy of SUZUKI OF AMERICA CORP.
  1. Inspect the front control valve body (345) casting for the following conditions:
    • Porosity
    • Cracks
    • Damaged machine surface
    • Chips or debris
    • Damage to valve bores
  2. Inspect all valves, springs, bushings, and clean all components in clean solvent.
    Fig 2: Identifying Solenoid Modulator Valve Spring & Solenoid Modulator Valve Bore Plug
    G04846353Courtesy of SUZUKI OF AMERICA CORP.
  3. Install the solenoid modulator valve (346).
  4. Install the solenoid modulator valve spring (347).
  5. Install the solenoid modulator valve bore plug (348).
  6. Install the sleeve/bore plug retainer (349).
    Fig 3: Identifying Second Coast Clutch Control Valve & Solenoid Modulator Valve Bore Plug
    G04846354Courtesy of SUZUKI OF AMERICA CORP.
  7. Install the second coast clutch (B1) control valve spring (358).
  8. Install the second coast clutch (B1) control valve (359).
  9. Install the solenoid modulator valve bore plug (348).
  10. Install the sleeve/bore plug retainer (349).
    Fig 4: Identifying Neutral Relay Valve & Solenoid Modulator Valve Bore Plug
    G04846355Courtesy of SUZUKI OF AMERICA CORP.
  11. Install the neutral relay valve (356).
  12. Install the neutral relay valve spring (357).
  13. Install the solenoid modulator valve bore plug (348).
  14. Install the sleeve/bore plug retainer (349).
    Fig 5: Identifying Forward Clutch Control Valve & Solenoid Modulator Valve Bore Plug
    G04846356Courtesy of SUZUKI OF AMERICA CORP.
  15. Install the forward clutch (C1) control valve (354).
  16. Install the solenoid modulator valve bore plug (348).
  17. Install the sleeve/bore plug retainer (349).
    Fig 6: Identifying Pressure Relief Valve Spring, Ball Check Valve & Fluid Strainer
    G04846357Courtesy of SUZUKI OF AMERICA CORP.
  18. Install the pressure relief valve spring (350).
  19. Install the pressure relief valve (351).
  20. Install the fluid strainer (352).
  21. Install the ball check valve (355).
  22. Install the 2 check valve compression springs (361).
  23. Install the 2 check valves (360).

    Reference: CONTROL VALVE BODY ASSEMBLY ASSEMBLE .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.