Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUZUKI2013SX4 CROSSOVER, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 14 (AUTOMATIC TRANSMISSION)DIAGNOSTIC INFORMATION AND PROCEDUREDTC P0730CIRCUIT/SYSTEM TESTING
2013 Suzuki SX4 Crossover, Automatic CVT Trans
Circuit/System Testing
2013 Suzuki SX4 Crossover, Automatic CVT TransSECTION Circuit/System Testing
WARNING: This page is about a different car, the 2007 Suzuki XL7. However, it is still accessible from the selected car via links, so may be relevant.
- Operate the vehicle in 2nd gear. The engine should not stall when shifting into 2nd gear.
- Inspect and repair as necessary, the control valve body assembly for a stuck 3-4, 4-5 solenoid valve or a stuck U1 shift valve. Refer to the CONTROL VALVE BODY ASSEMBLY DISASSEMBLE procedure.
- Observe the scan tool Transmission OSS parameter. The reading should correspond to a known properly functioning OSS.
- If the OSS is malfunctioning, replace the Transmission Output Speed Sensor (OSS). Refer to the OUTPUT SPEED SENSOR REPLACEMENT procedure.
- Stop the vehicle, apply the parking brake, engine at idle, select P (park) using the Shift Control.
- Observe the scan tool Transmission ISS parameter. The reading should be within 400-800 RPM.
- If the ISS parameter is not within the specified range, replace the Transmission Input Speed Sensor (OSS). Refer to the INPUT SPEED SENSOR REPLACEMENT procedure.
- Firmly apply the brake, select D (drive) using the Shift Control.
- Observe the scan tool TCC Slip Speed. The reading should be within 0-100 RPM.
- If the TCC Slip Speed is not within the specified range
- Ignition ON, engine OFF, command shift solenoid 1 ON and OFF with a scan tool. The solenoid should click when commanded ON.
- If the solenoid does not click, replace the 1st shift solenoid valve assembly. Refer to CONTROL VALVE BODY ASSEMBLY DISASSEMBLE .
- Command shift solenoid 5 ON and OFF with a scan tool. The solenoid should click when commanded ON.
- If the solenoid does not click, replace the reverse shift solenoid valve assembly. Refer to CONTROL VALVE BODY ASSEMBLY DISASSEMBLE .
- Perform a line pressure test. Refer to LINE PRESSURE CHECK procedure.
- Remove the Control valve body cover. Refer to CONTROL VALVE BODY COVER REMOVAL procedure.
- Inspect the inside of the control valve body cover for excessive sediment. There should not be excessive sediment.
- If excessive sediment is found inspect and replace as necessary the Low clutch sprag, Forward clutch, and 1-2, reverse clutch. Refer to FRONT INTERNAL GEAR AND OVERRUN CLUTCH ASSEMBLE , FORWARD AND DIRECT CLUTCH ASSEMBLY ASSEMBLE and 1-2 Reverse Clutch Assemble procedures.
- Inspect the control valve body assembly for the following conditions. Refer to CONTROL VALVE REAR BODY DISASSEMBLE and MIDDLE CONTROL VALVE BODY DISASSEMBLE . The conditions should not be found.
- Stuck shift pressure relay valve
- Stuck M1 shift valve
- Line pressure control solenoid valve assembly stuck closed
- If any of the above conditions are found, replace the valve body assembly. Refer to CONTROL VALVE BODY REPLACEMENT procedure.
- Verify that the control valve body has been serviced within the past 3 months.
- If the control valve body has not been serviced, replace the control valve body assembly. Refer to CONTROL VALVE BODY REPLACEMENT procedure.
- If all circuits and components test normal, replace the transmission.
- If all circuits and components test normal, replace the transmission.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.