Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUZUKI2013KIZASHI SPORT GTS, FWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 79 (BODY ELECTRICAL CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESFAIL-SAFE TABLE
2013 Suzuki Kizashi Sport GTS, FWD
Fail-Safe Table
2013 Suzuki Kizashi Sport GTS, FWDSECTION Fail-Safe Table
WARNING: This page is about a different car, the 2010 Suzuki Kizashi. However, it is still accessible from the selected car via links, so may be relevant.
When DTC is detected, BCM changes fail-safe mode as long as malfunction continues to exist but that mode is canceled when BCM recovers normal condition.
FAIL-SAFE CHART
| DTC | DTC name | Fail-safe operation |
|---|---|---|
| B1120 | BCM Internal Defect | - |
| B1132 | 5 V System Voltage too Low | BCM stops 5 V power supply of "G05-8" terminal. |
| B1133 | Battery Voltage too High | - |
| B1141 | Outside Air Temperature (Ambient Temperature) Sensor Circuit Open | BCM outputs outside air temperature -40°C (-40°F). |
| B1142 | Outside Air Temperature (Ambient Temperature) Sensor Circuit Short to Ground | BCM outputs outside air temperature 87.5°C (189.5°F). |
| B1145 | A/C Evaporator Temperature Sensor Circuit High | BCM outputs evaporator temperature -40°C (-40°F). |
| B1146 | A/C Evaporator Temperature Sensor Circuit Low | BCM outputs evaporator temperature 60 °C (140 °F). |
| B1157 | Air Bag Deployment Signal Input | BCM stops lock operation at power door lock switch until ignition mode of keyless push start system is turned OFF. |
| B1670 | Rain/Light Sensor Malfunction | Refer to LIGHTING SYSTEM DIAGNOSIS FUNCTION and RAIN-SENSING WIPER DIAGNOSIS FUNCTION . |
| B1680 | CAN Invalid Data from ECM | BCM stops vehicle dynamics synthetic control. |
| B1681 | CAN Invalid Data from TCM | - |
| B1682 | CAN Invalid Data from 4WD Control Module | BCM stops vehicle dynamics synthetic control. |
| B1683 | Yaw Rate Information Mismatched | BCM stops vehicle dynamics synthetic control. |
| B1684 | CAN Invalid Data from P/S Control Module | BCM stops vehicle dynamics synthetic control. |
| B1685 | CAN Invalid Data from ESP® Control Module | - |
| B1686 | CAN Invalid Data from Longitudinal G Sensor | - |
| B1687 | CAN Invalid Data from Lateral G Sensor | BCM stops vehicle dynamics synthetic control. |
| B1688 | CAN Invalid Data from Yaw Rate Sensor | BCM stops vehicle dynamics synthetic control. |
| B1689 | CAN Invalid Data from Wheel Speed Sensor | BCM stops vehicle dynamics synthetic control. |
| B1690 | Steering Angle Sensor Malfunction | BCM stops vehicle dynamics synthetic control. |
| B1691 | CAN Invalid Data from Steering Angle Sensor | BCM stops vehicle dynamics synthetic control. |
| B1692 | CAN Invalid Data from Steering Angle Sensor | BCM stops vehicle dynamics synthetic control. |
| B1693 | CAN Invalid Data from P/S Control Module | BCM stops vehicle dynamics synthetic control. |
| B1694 | CAN Invalid Data from P/S Control Module | BCM stops vehicle dynamics synthetic control. |
| B1695 | CAN Invalid Data from ESP® Control Module | BCM stops vehicle dynamics synthetic control. |
| B1696 | CAN Invalid Data from ESP® Control Module | BCM stops vehicle dynamics synthetic control. |
| B1901 | Internal Control Module Memory Check Sum Error | - |
| B1902 | Control Module Programming Error | - |
| U0073 | Control Module Communication Bus Off | - |
| U0100 | Lost Communication with ECM | BCM stops vehicle dynamics synthetic control. |
| U0101 | Lost Communication with TCM | BCM controls with default value. |
| U0114 | Lost Communication with 4-Wheel Drive Control Module | BCM stops vehicle dynamics synthetic control. |
| U0121 | Lost Communication with ABS/ESP® Control Module | BCM stops vehicle dynamics synthetic control. |
| U0126 | Lost Communication with Steering Angle Sensor | BCM stops vehicle dynamics synthetic control. |
| U0131 | Lost Communication with Power Steering Control Module | BCM stops vehicle dynamics synthetic control. |
| U0141 | Lost Communication with Body Control Module "keyless start" | BCM controls with default value. |
| U0151 | Lost Communication with Restraints Control Module | BCM controls with default value. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | BCM controls with default value. |
| U0164 | Lost Communication with HVAC Control Module | BCM controls with default value. |
| U0231 | Lost Communication with Rain Sensing Module | BCM controls with default value. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.