Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUZUKI2013KIZASHI SPORT GTS, FWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 79 (BODY ELECTRICAL CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESDTC TABLE
2013 Suzuki Kizashi Sport GTS, FWD
DTC Table
2013 Suzuki Kizashi Sport GTS, FWDSECTION DTC Table
WARNING: This page is about a different car, the 2010 Suzuki Kizashi. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
- The DTC No. with asterisk (*) does not memorize history DTC.
- When BCM detects DTC B1120, display "SERVICE BCM SYSTEM" on the information display in combination meter to warn the driver.
DTC DETECTING CONDITION CHART
| DTC | DTC name | DTC detecting condition |
|---|---|---|
| B1120* | BCM Internal Defect | BCM internal failure. |
| B1132 | 5 V System Voltage too Low | "G05-8" terminal voltage is lower than 2.5 V for specified time continuously. |
| B1133 | Battery Voltage too High | Backup power supply circuit voltage from "DOME" fuse is continuously higher than 16.0 V for specified time. |
| B1141 | Outside Air Temperature (Ambient Temperature) Sensor Circuit Open | Outside air temperature sensor signal circuit voltage is higher than 4.85 V for specified time continuously. |
| B1142 | Outside Air Temperature (Ambient Temperature) Sensor Circuit Short to Ground | Outside air temperature sensor signal circuit voltage is lower than 0.15 V for specified time continuously. |
| B1145 | A/C Evaporator Temperature Sensor Circuit High | Evaporator temperature sensor signal circuit voltage is higher than 4.85 V for specified time continuously. |
| B1146 | A/C Evaporator Temperature Sensor Circuit Low | Evaporator temperature sensor signal circuit voltage is lower than 0.15 V for specified time continuously. |
| B1157 | Air Bag Deployment Signal Input | Air bag deployment signal is fed from SDM to BCM. |
| B1670* | Rain/Light Sensor Malfunction | BCM detected malfunction related to rain/light sensor. |
| B1680 | CAN Invalid Data from ECM | BCM detected abnormality in control data transmitted by ECM through CAN communication. |
| B1681 | CAN Invalid Data from TCM | BCM detected abnormality in control data transmitted by TCM through CAN communication. |
| B1682 | CAN Invalid Data from 4WD Control Module | BCM detected abnormality in control data transmitted by 4WD control module through CAN communication. |
| B1683* | Yaw Rate Information Mismatched | Difference between target yaw rate calculated by BCM and actual yaw rate transmitted from ESP® control module via CAN communication is continuously higher than specified value for specified time. |
| B1684 | CAN Invalid Data from P/S Control Module | BCM detected abnormality in control data transmitted by P/S control module through CAN communication. |
| B1685* | CAN Invalid Data from ESP® Control Module |
|
| B1686* | CAN Invalid Data from Longitudinal G Sensor | BCM detected abnormality in longitudinal G data transmitted by ESP® control module through CAN communication. |
| B1687* | CAN Invalid Data from Lateral G Sensor | BCM detected abnormality in lateral G data transmitted by ESP® control module through CAN communication. |
| B1688* | CAN Invalid Data from Yaw Rate Sensor | BCM detected abnormality in yaw rate data transmitted by ESP® control module through CAN communication. |
| B1689* | CAN Invalid Data from Wheel Speed Sensor | BCM detected abnormality in wheel speed data transmitted by ESP® control module through CAN communication. |
| B1690* | Steering Angle Sensor Malfunction |
|
| B1691 | CAN Invalid Data from Steering Angle Sensor | BCM received abnormal CAN communication data from steering angle sensor. |
| B1692 | CAN Invalid Data from Steering Angle Sensor | BCM received abnormal CAN communication data from steering angle sensor. |
| B1693 | CAN Invalid Data from P/S Control Module | BCM received abnormal CAN communication data from P/S control module. |
| B1694 | CAN Invalid Data from P/S Control Module | BCM received abnormal CAN communication data from P/S control module. |
| B1695 | CAN Invalid Data from ESP® Control Module | BCM received abnormal CAN communication data from ESP® control module. |
| B1696 | CAN Invalid Data from ESP® Control Module | BCM received abnormal CAN communication data from ESP® control module. |
| B1901* | Internal Control Module Memory Check Sum Error | BCM internal failure. (check sum error) |
| B1902* | Control Module Programming Error | BCM internal failure. (programming error) |
| U0073 | Control Module Communication Bus Off | BCM fails to transmit and receive the data via CAN for specified time continuously. |
| U0100 | Lost Communication with ECM | Receiving error of the data from ECM via CAN for specified time continuously. |
| U0101 | Lost Communication with TCM | Receiving error of the data from TCM via CAN for specified time continuously. |
| U0114 | Lost Communication with 4-Wheel Drive Control Module | Receiving error of the data from 4WD control module via CAN for specified time continuously. |
| U0121 | Lost Communication with ABS/ESP® Control Module | Receiving error of the data from ESP® control module via CAN for specified time continuously. |
| U0126 | Lost Communication with Steering Angle Sensor | Receiving error of the data from steering angle sensor via CAN for specified time continuously. |
| U0131 | Lost Communication with Power Steering Control Module | Receiving error of the data from P/S control module via CAN for specified time continuously. |
| U0141 | Lost Communication with Body Control Module "keyless start" | Receiving error of the data from keyless start control module via CAN for specified time continuously. |
| U0151 | Lost Communication with Restraints Control Module | Receiving error of the data from SDM via CAN for specified time continuously. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | Receiving error of the data from combination meter via CAN for specified time continuously. |
| U0164 | Lost Communication with HVAC Control Module | Receiving error of the data from HVAC control module via CAN for specified time continuously. |
| U0231 | Lost Communication with Rain Sensing Module | Receiving error of the data from rain/light sensor via CAN for specified time continuously. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.