Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Scan Tool Data Definitions - Engine Electrical
2009 Suzuki XL-7 2WD V6-3.6LSECTION Scan Tool Data Definitions - Engine Electrical
Scan Tool Data Definitions - Engine Electrical
Battery Voltage
The scan tool displays 0-20 Volts. The scan tool displays the voltage as received by the Module.
Battery Voltage Signal
The scan tool displays 0-20 Volts. The scan tool displays the voltage as received by the Module.
Crank Request Signal
The scan tool displays Yes/No. The scan tool displays No until the ignition is placed into the START position then Yes is displayed.
GEN F-Terminal Signal
The scan tool displays 0-100%. The display indicates the generator F terminal duty cycle in percent. The scan tool displays 0-5% until the engine is running, then the percentage value varies depending on engine or electrical loads.
GEN L-Terminal Command
The scan tool displays 0-100%. The scan tool displays the percentage of the output voltage of the generator.
GEN L-Terminal Circuit Status
The scan tool displays Incomplete, Short Gnd / Open, Short to B+, or OK. The scan tool displays the status of the GEN L Terminal circuit.
Ignition 1 Signal
The scan tool displays 0-20 Volts. The scan tool displays the voltage as received on the Ignition 1 circuit to the module.
Ignition Accessory Signal
The scan tool displays ON/OFF. The scan tool displays if the ignition 0 signal is On or OFF.
Ignition Voltage Signal
The scan tool displays Present/Not Present. The scan tool displays the status of the ignition voltage signal on the theft deterrent module (TDM).
PNP Switch (If Equipped)
The scan tool displays Park/Neutral or In Gear. The scan tool displays the position of the transmission setting.
Start Disabled
The scan tool displays YES/NO. The scan tool displays YES if the TDM has disabled the starting function.
Starter Relay Command
The scan tool displays ON/OFF. The scan tool displays Off until the ignition is placed into the CRANK position, then it reads On.
Starter Relay Circuit Status
The scan tool displays Incomplete, Short Gnd/Open, Short to B+, or OK. The scan tool displays the status of the STRTR relay.
Start Up State of Charge
The scan tool displays 1-100%. The scan tool displays the state of charge at initial key up.
Prev. State of Charge
The scan tool displays 0-100%. The scan tool displays the state of charge from the previous ignition cycle.
State of Charge
The scan tool displays 0-100%. The scan tool displays the present state of charge.
State of Charge Low
The scan tool displays YES/NO. The scan tool displays YES if the present state of charge is low.
Battery Voltage
The scan tool displays 0-20 Volts. The scan tool displays the voltage as received by the Module.
Battery Voltage Signal
The scan tool displays 0-20 Volts. The scan tool displays the voltage as received by the Module.
Crank Request Signal
The scan tool displays Yes/No. The scan tool displays No until the ignition is placed into the START position then Yes is displayed.
GEN F-Terminal Signal
The scan tool displays 0-100%. The display indicates the generator F terminal duty cycle in percent. The scan tool displays 0-5% until the engine is running, then the percentage value varies depending on engine or electrical loads.
GEN L-Terminal Command
The scan tool displays 0-100%. The scan tool displays the percentage of the output voltage of the generator.
GEN L-Terminal Circuit Status
The scan tool displays Incomplete, Short Gnd / Open, Short to B+, or OK. The scan tool displays the status of the GEN L Terminal circuit.
Ignition 1 Signal
The scan tool displays 0-20 Volts. The scan tool displays the voltage as received on the Ignition 1 circuit to the module.
Ignition Accessory Signal
The scan tool displays ON/OFF. The scan tool displays if the ignition 0 signal is On or OFF.
Ignition Voltage Signal
The scan tool displays Present/Not Present. The scan tool displays the status of the ignition voltage signal on the theft deterrent module (TDM).
PNP Switch (If Equipped)
The scan tool displays Park/Neutral or In Gear. The scan tool displays the position of the transmission setting.
Start Disabled
The scan tool displays YES/NO. The scan tool displays YES if the TDM has disabled the starting function.
Starter Relay Command
The scan tool displays ON/OFF. The scan tool displays Off until the ignition is placed into the CRANK position, then it reads On.
Starter Relay Circuit Status
The scan tool displays Incomplete, Short Gnd/Open, Short to B+, or OK. The scan tool displays the status of the STRTR relay.
Start Up State of Charge
The scan tool displays 1-100%. The scan tool displays the state of charge at initial key up.
Prev. State of Charge
The scan tool displays 0-100%. The scan tool displays the state of charge from the previous ignition cycle.
State of Charge
The scan tool displays 0-100%. The scan tool displays the present state of charge.
State of Charge Low
The scan tool displays YES/NO. The scan tool displays YES if the present state of charge is low.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.