Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Scan Tool Data Definitions - Antilock Brake System
2009 Suzuki XL-7 2WD V6-3.6LSECTION Scan Tool Data Definitions - Antilock Brake System
Scan Tool Data Definitions - Antilock Brake System
The ABS scan tool data definitions contain a brief description of all ABS related parameters available on the scan tool. The parameters available on the scan tool are listed below in alphanumeric order.
ABS Active: The scan tool displays Yes/No. The scan tool displays No when a when not active.
ABS Failed: The scan tool displays On/Off. The scan tool displays On when a when the ABS Failed.
Battery Voltage Signal: The scan tool will display Voltage depending on the state of the battery and charging system.
Brake Fluid Level Sensor: The scan tool displays OK/Low The scan tool indicates Low when the brake fluid sensor detects fluid lose.
BPP Signal: The scan tool will display Released/Applied depending on the state of the brake pedal position.
Delivered Torque: The scan tool displays 25-95%. The scan tool displays 25% when the powertrain control module (PCM) is providing the minimum percentage of available torque in an attempt to eliminate wheel slip.
DRP Active: The scan tool will display Yes/No depending on the state of the DRP.
DRP Disabled: The scan tool will display Yes/No depending on the state of the DRP.
Lateral Accelerometer Input The scan tool displays m/s^2. The lateral accelerometer signal from the lateral accelerometer sensor, roughly 2.5 volts equals 0 g lateral acceleration.
LF Inlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
LF Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
LF Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
Low Tire Press. Lamp The scan tool displays ON or OFF.
LR Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
LR Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
Panic Brake Assist Failed: The scan tool displays No/Yes. The scan tool displays No when the Panic brake Assist functions properly.
Pump Motor Command Voltage: The scan tool displays battery voltage when the pump motor is commanded on.
Requested Torque: The scan tool displays 40-95%. The scan tool displays 40% when the electronic brake control module (EBCM) requests the minimum percentage of available torque in an attempt to eliminate wheel slip.
RF Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Outlet solenoid is commanded on.
RF Inlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
RF Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
RR Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
RR Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
RR Inlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
Steering Wheel Position: The scan tool displays degrees. The steering wheel position signal varies from 720°+ to & 720°-.
Steering Sensor: The scan tool displays centered or uncentered.
TCS Active: The scan tool displays Yes or No. The scan tool displays Yes if the TCS indicator is currently being commanded ON.
TCS Failed: The scan tool displays Yes/No. The scan tool displays Yes when the TCS will not engage caused from a malfunction.
VSES Active: The scan tool displays Yes or No. Indicates if Vehicle Stability Enhancement System (VSES) is currently active.
VSES Failed: The scan tool displays Yes or No. Indicates if the EBCM disabled VSES due to a malfunction.
Yaw Rate Sensor Input: The scan tool displays m/s^2. The yaw rate signal from the yaw rate sensor, roughly 2.5 volts equals 0°/second yaw rate.
The ABS scan tool data definitions contain a brief description of all ABS related parameters available on the scan tool. The parameters available on the scan tool are listed below in alphanumeric order.
ABS Active: The scan tool displays Yes/No. The scan tool displays No when a when not active.
ABS Failed: The scan tool displays On/Off. The scan tool displays On when a when the ABS Failed.
Battery Voltage Signal: The scan tool will display Voltage depending on the state of the battery and charging system.
Brake Fluid Level Sensor: The scan tool displays OK/Low The scan tool indicates Low when the brake fluid sensor detects fluid lose.
BPP Signal: The scan tool will display Released/Applied depending on the state of the brake pedal position.
Delivered Torque: The scan tool displays 25-95%. The scan tool displays 25% when the powertrain control module (PCM) is providing the minimum percentage of available torque in an attempt to eliminate wheel slip.
DRP Active: The scan tool will display Yes/No depending on the state of the DRP.
DRP Disabled: The scan tool will display Yes/No depending on the state of the DRP.
Lateral Accelerometer Input The scan tool displays m/s^2. The lateral accelerometer signal from the lateral accelerometer sensor, roughly 2.5 volts equals 0 g lateral acceleration.
LF Inlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
LF Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
LF Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
Low Tire Press. Lamp The scan tool displays ON or OFF.
LR Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
LR Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
Panic Brake Assist Failed: The scan tool displays No/Yes. The scan tool displays No when the Panic brake Assist functions properly.
Pump Motor Command Voltage: The scan tool displays battery voltage when the pump motor is commanded on.
Requested Torque: The scan tool displays 40-95%. The scan tool displays 40% when the electronic brake control module (EBCM) requests the minimum percentage of available torque in an attempt to eliminate wheel slip.
RF Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Outlet solenoid is commanded on.
RF Inlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
RF Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
RR Wheel Speed Sensor: The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
RR Outlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
RR Inlet Solenoid Command: The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
Steering Wheel Position: The scan tool displays degrees. The steering wheel position signal varies from 720°+ to & 720°-.
Steering Sensor: The scan tool displays centered or uncentered.
TCS Active: The scan tool displays Yes or No. The scan tool displays Yes if the TCS indicator is currently being commanded ON.
TCS Failed: The scan tool displays Yes/No. The scan tool displays Yes when the TCS will not engage caused from a malfunction.
VSES Active: The scan tool displays Yes or No. Indicates if Vehicle Stability Enhancement System (VSES) is currently active.
VSES Failed: The scan tool displays Yes or No. Indicates if the EBCM disabled VSES due to a malfunction.
Yaw Rate Sensor Input: The scan tool displays m/s^2. The yaw rate signal from the yaw rate sensor, roughly 2.5 volts equals 0°/second yaw rate.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.