Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Scan Tool Data Definitions - Immobilizer
2009 Suzuki XL-7 2WD V6-3.6LSECTION Scan Tool Data Definitions - Immobilizer
Scan Tool Data Definitions - Immobilizer
Auto Learn
The scan tool displays Enabled when the 30 minute auto learn reprogramming procedure is available as a valid programming option.
Auto Learn Counter
The scan tool displays the count value when using the 30 minute reprogramming procedure. Three 10 minute cycles, or three counts, are required to complete the 30 minute auto learn reprogramming procedure.
Auto Learn Timer
The scan tool displays the time in minutes remaining by the TDM to learn a valid code from the transponder using the 30 minute auto learn reprogramming procedure.
Battery Voltage
The scan tool displays battery voltage at the TDM.
ECM in VTD Fail Enable
The scan tool will display Yes when the ECM is fail enabled.
Ignition Voltage
The scan tool displays ignition voltage at the TDM.
Learned Keys Required
The scan tool displays the numbers of learned keys require to initialize the Adding Keys procedure. Domestic vehicles require 1 key, while export and Canadian vehicles require 2.
Master Keys Learned
The scan tool displays the number of learned master keys.
PCM Auto Learn Timer
The scan tool displays Active when the PCM is in auto learn.
PCM Fail Enable
The scan tool displays Active when the PCM is in the fail enable state.
PCM Fuel Continue
The scan tool displays the status of vehicle fueling. An Inactive value would indicator an invalid or no fuel continue message was received. Vehicle starting is not allowed in this situation. An Active value would indicated a valid fuel continue message was received and vehicle starting is allowed.
PCM Password Learning
The scan tool displays Enabled when the PCM is in learn mode.
PCM Password Status
The scan tool displays the PCM's current response to the theft password.
Power Mode
The scan tool displays the current vehicle power mode.
Previous TDM State
The scan tool displays the TDM state of the last ignition cycle.
Security Indicator Command
The scan tool displays the state of the BCM commanding the security indicator. The scan tool displays ON or, OFF, as commanded by the BCM.
Tamper Status
The scan tool displays Active when a tamper condition is detected.
Telltale Status
The scan tool displays the state of the body control module (BCM) commanding the security indicator. The scan tool displays ON, OFF, FLASH, or INVALID as commanded by the TDM.
TDM State
The scan tool displays the TDM state for the current ignition cycle.
Auto Learn
The scan tool displays Enabled when the 30 minute auto learn reprogramming procedure is available as a valid programming option.
Auto Learn Counter
The scan tool displays the count value when using the 30 minute reprogramming procedure. Three 10 minute cycles, or three counts, are required to complete the 30 minute auto learn reprogramming procedure.
Auto Learn Timer
The scan tool displays the time in minutes remaining by the TDM to learn a valid code from the transponder using the 30 minute auto learn reprogramming procedure.
Battery Voltage
The scan tool displays battery voltage at the TDM.
ECM in VTD Fail Enable
The scan tool will display Yes when the ECM is fail enabled.
Ignition Voltage
The scan tool displays ignition voltage at the TDM.
Learned Keys Required
The scan tool displays the numbers of learned keys require to initialize the Adding Keys procedure. Domestic vehicles require 1 key, while export and Canadian vehicles require 2.
Master Keys Learned
The scan tool displays the number of learned master keys.
PCM Auto Learn Timer
The scan tool displays Active when the PCM is in auto learn.
PCM Fail Enable
The scan tool displays Active when the PCM is in the fail enable state.
PCM Fuel Continue
The scan tool displays the status of vehicle fueling. An Inactive value would indicator an invalid or no fuel continue message was received. Vehicle starting is not allowed in this situation. An Active value would indicated a valid fuel continue message was received and vehicle starting is allowed.
PCM Password Learning
The scan tool displays Enabled when the PCM is in learn mode.
PCM Password Status
The scan tool displays the PCM's current response to the theft password.
Power Mode
The scan tool displays the current vehicle power mode.
Previous TDM State
The scan tool displays the TDM state of the last ignition cycle.
Security Indicator Command
The scan tool displays the state of the BCM commanding the security indicator. The scan tool displays ON or, OFF, as commanded by the BCM.
Tamper Status
The scan tool displays Active when a tamper condition is detected.
Telltale Status
The scan tool displays the state of the body control module (BCM) commanding the security indicator. The scan tool displays ON, OFF, FLASH, or INVALID as commanded by the TDM.
TDM State
The scan tool displays the TDM state for the current ignition cycle.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.